2022 Developer Survey is open! Take survey.

3D Printing Stack Exchange is a question and answer site for 3D printing enthusiasts. It only takes a minute to sign up.

Sign up to join this community
Anybody can ask a question
Anybody can answer
The best answers are voted up and rise to the top

Top Questions

0 votes
0 answers
5 views

I have stringing issues with my Anycubic Chiron printer

0 votes
0 answers
2 views

I have a Ender 3 S1 Pro and can't restart a print after a pause at height

1 vote
0 answers
4 views

Is there printable optical-grade resin?

9 votes
3 answers
1k views

Can I really throw failed PLA prints on compost?

0 votes
0 answers
10 views

Wavy walls on one axis (not ringing)

0 votes
0 answers
13 views

Resin LCD print not printing first layers properly, resulting in a reduction of the height of the object

2 votes
1 answer
22 views

Nozzle digs into material and extruder starts skipping after some layers

0 votes
2 answers
75 views

Ender 5 SKR Mini E3 -- After Heating the Hot End Assembly Runs into the side of the printer

1 vote
3 answers
213 views

3D Print something as flexible as a cloth with PLA?

1 vote
1 answer
115 views

Print bulging and curling on the edges

2 votes
2 answers
33 views

Cura variables and initial G-code commands

1 vote
1 answer
19 views

Wall thickness and line count in Cura, are they redundant, or do they multiply?

0 votes
1 answer
18 views

Creality CR-6 SE heatblock replacement

1 vote
0 answers
33 views

What causes different fluoresence of PLA from different sources?

0 votes
0 answers
19 views

Print Fail: Partial Mess - What are possible causes?

1 vote
0 answers
15 views

Ender 3 Pro keeps stopping after about 2 or 3 layers. SD card maybe?

1 vote
1 answer
510 views

Creality CR 6 SE Z-axis issue

0 votes
1 answer
30 views

Anycubic Vyper Filament Stripping

0 votes
0 answers
12 views

Prusa MK3S not printing during printing but extruder working and First Layer working fine

6 votes
2 answers
339 views

Why are the STL files for the Ultrascope telescope at 45 degree angle?

1 vote
1 answer
19 views

Adjustable Angle for a 1.5 inch OLED screen

0 votes
2 answers
25 views

What's causing this lack of layer adhesion after a crash?

1 vote
0 answers
19 views

Pros and cons of the two(+?) kinds of bimetal heatbreaks

0 votes
0 answers
19 views

Do flyback diode filters in stepper circuits improve print quality?

1 vote
1 answer
611 views

Cura: How to prevent my 3D printer from auto cooling after prints

0 votes
1 answer
144 views

Pause, rehome X/Y, resume

1 vote
1 answer
52 views

Large format heated bed

1 vote
2 answers
38 views

Any way to print all the layers of a 3D (STL)?

0 votes
0 answers
24 views

What is the 4pin connector next to this USB on the Creality 4.2.3 board?

1 vote
1 answer
42 views

Ender 3D Pro extruder stepper motor shaft length

2 votes
2 answers
39 views

Where can I change the nozzle diameter in Cura? Why is mine missing?

0 votes
0 answers
12 views

Suggestions for heat element and temperature sensor for heating a brass printer table (dim 25x25x10mm)

1 vote
1 answer
120 views

TronXY X1 Configure bed offsets

1 vote
1 answer
35 views

Browsing and printing print files (G-code) stored in OctoPrint from printer's screen

3 votes
2 answers
279 views

Filament based printing what operator behaviors contribute to an increased need to relevel a bed?

2 votes
2 answers
245 views

Under-extrusion halfway into print - Dremel 3D45 -PETG

6 votes
5 answers
7k views

Why is my 3D printer over extruding when I have set the flow rate very low

1 vote
1 answer
35 views

Effects of bad power supply on temperature/flow?

1 vote
1 answer
26 views

How do I check the belts on my Ender 3?

2 votes
1 answer
21 views

Are there printer firmware specifics when adding printer profiles to slicer software?

1 vote
1 answer
51 views

Chitubox stopped slicing files correctly

1 vote
0 answers
484 views

Ender 3 Pro with BLtouch + BigTreeTech Auto level not compensating

1 vote
1 answer
154 views

Mixing (closed loop) stepper drivers on MKS main board

1 vote
1 answer
60 views

Anycubic i3 Mega layers don't stick together/are too thin

1 vote
2 answers
136 views

Why do concrete 3D printers zigzag?

2 votes
2 answers
45 views

Can OpenSCAD bend text (project it on curved surface)?

0 votes
2 answers
3k views

Z offset in Marlin is not working recently

0 votes
0 answers
20 views

X-axis taper problem


Looking for more? Browse the complete list of questions, or popular tags. Help us answer unanswered questions.