3D Printing Stack Exchange is a question and answer site for 3D printing enthusiasts. It only takes a minute to sign up.

Sign up to join this community
Anybody can ask a question
Anybody can answer
The best answers are voted up and rise to the top

Top Questions

1 vote
1 answer
15 views

Resin printers: What effect does altering the lift distance on a Resin printer have, and what are the consequences of getting it wrong?

0 votes
0 answers
28 views

Print turns into spaghetti on Ender 3 Pro

1 vote
0 answers
13 views

Print stop/starts after 3Dtouch installation

0 votes
0 answers
12 views

DIY 3D printer Z-axis problems

2 votes
1 answer
34 views

Large infill top layer almost immediately gets ruined trying to bridge

2 votes
0 answers
20 views

Layers peeling off in resin prints

1 vote
0 answers
15 views

Chitubox: Is it possible to place a hollow object flat on the build plate and use internal supports?

1 vote
2 answers
45 views

What is causing the thermal runaway error E1? [duplicate]

0 votes
0 answers
24 views

Static electricity underneath the print with mystery adhesion and warping

1 vote
1 answer
22 views

What is the acceptable resistance of a functioning heater cartridge on my Creality Ender-5 Pro printer?

2 votes
1 answer
26 views

Creality Ender 6 Heating Failed

2 votes
1 answer
60 views

Meshmixer create solid

-1 votes
1 answer
31 views

Convert 3D file format [closed]

4 votes
0 answers
55 views

Clogging from heat creep, but only in the nozzle itself?

0 votes
0 answers
23 views

The bed of my Ender-4 does not go down during printing!

0 votes
0 answers
34 views

Marlin 2.1 reboots before printing model when power recovery is enabled

0 votes
3 answers
67 views

Filament not being extruded

0 votes
0 answers
20 views

Specs for a stepper motor

1 vote
1 answer
50 views

Missing filament at Z seam

0 votes
2 answers
93 views

Can you 3D print an electrical connection

1 vote
1 answer
47 views

How to change the time format on LCD screen in Marlin 2.1?

0 votes
1 answer
116 views

Are thick layer lines easier to sand and fill than thin layer lines for low detail objects

0 votes
2 answers
61 views

Is there a way to make my 3D prints airtight?

1 vote
3 answers
57 views

Filament end expanding and seizing

0 votes
1 answer
53 views

Where/how can I connect a physical Emergency Stop panic button directly to a RAMPS 1.4 board to quickly stop all stepper movement?

2 votes
1 answer
46 views

Stepper motor D shaft to Lego axle adapter

2 votes
2 answers
26 views

Printing half size after board replacement

0 votes
0 answers
50 views

Creality Ender 6 does not boot beyond the boot screen

1 vote
4 answers
49 views

When I print with a raft on my 3D printer, the raft will not peel off. What settings can I change to fix this?

2 votes
3 answers
78 views

Thermal Runaway issues on Ender 3 Pro even after replacing thermistor and heater cartridge

4 votes
1 answer
65 views

Why is it more common to move the extruder on the Z-axis than the print bed, in consumer FDM printers?

1 vote
1 answer
46 views

Ender 3 Thermal Runaway Error when booting up

2 votes
0 answers
26 views

Anet ET4 - Thermal Runaway immediately after Boot

3 votes
1 answer
35 views

Meaning of light prompts on Ender 6 motherboard

2 votes
1 answer
20 views

Connecting controller fan on RAMPS 1.4 for Marlin

3 votes
2 answers
48 views

Can you fillet the base of an object without needing supports? Is there a recommended radius?

0 votes
1 answer
44 views

Creality CR-6 SE heatblock replacement

2 votes
1 answer
54 views

Printer stops printing at the same spot for every model

0 votes
2 answers
30 views

Aside from aesthetics, are there any benefits to metal infused 3d printing filament?

0 votes
0 answers
40 views

Moving bed Y-axis belt keeps skipping after replacement

1 vote
1 answer
104 views

Solution for rewinding badly wound filament

2 votes
2 answers
90 views

Where can I change the nozzle diameter in Cura? Why is mine missing?

2 votes
1 answer
60 views

PLA Globbing up on the Extruder Nozzle

1 vote
2 answers
49 views

Commercial use? 3D scans of museum artifacts

1 vote
2 answers
93 views

Saggy vase walls. What are the tricks to successful vase mode printing?

1 vote
1 answer
113 views

Nozzle scraping bed on Ender 3 with CR Touch

0 votes
0 answers
28 views

Waterproof/resistent cutouts

0 votes
1 answer
30 views

When printing multiple objects at once, or traveling over gaps in prints, I get a lot of stringing. How can I help this?


Looking for more? Browse the complete list of questions, or popular tags. Help us answer unanswered questions.