3D Printing

Teacher

 Teacher
Answer a question with score of 1 or more.
Awarded 1426 times.
Why is my 3D printer over extruding when I have set the flow rate very low
Awarded 2 days ago
G29 UBL G-code - every request levels bed?
Awarded May 15 at 13:20
Ender 3 pro extruder skipping steps, tried multiple things
Awarded May 14 at 16:12
First layer rippling and no filament in certain areas
Awarded May 13 at 5:26
Cura not allowing full print area to used
Awarded May 11 at 19:06
What is causing these severe print errors on an Ender 3?
Awarded May 11 at 8:26
Best material for compression?
Awarded May 11 at 3:27
Continuing a failed print when you have Auto Mesh Bed Leveling
Awarded May 10 at 13:40
Creality Ender 3 Pro: Problem with Z-axis inaccuracy (squashed layers?)
Awarded May 7 at 20:00
How to work with PETG? Settings, caveats, etc
Awarded May 6 at 12:25
(post deleted or otherwise unavailable)
Awarded May 4 at 22:41
Wait for click to continue
Awarded May 4 at 16:40
alternative to Mic-6 bed plate
Awarded Apr 30 at 13:06
Do print issues (extrusion, blockage, etc...) become less of a problem with more expensive printers?
Awarded Apr 28 at 17:45
Strange stringing-like activity when printing face shields
Awarded Apr 26 at 13:27
When Z-axis is autohoming the print head moves too far to the right and starts grinding
Awarded Apr 16 at 18:20
Tuning line width and flow compensation in Cura
Awarded Apr 11 at 13:57
Tuning line width and flow compensation in Cura
Awarded Apr 11 at 9:06
Generating height map with Rep Rap
Awarded Apr 9 at 20:26
Humidity sensor says drybox isn't that dry - are my expectations unrealistic or is something wrong?
Awarded Apr 3 at 11:25
Ender 3 v2 temperature drop
Awarded Mar 30 at 2:16
Problems with stock gear with no screw on Ender 3 pro
Awarded Mar 29 at 15:47
Creality CR-10S Pro V2 Auto Bed Leveling probe sticks
Awarded Mar 27 at 7:17
Drop in temperature after couple layers
Awarded Mar 26 at 17:27
No distance between the nozzle and the print bed level at the center (1) position after bed leveling
Awarded Mar 23 at 14:56
Ender 3 with BLTouch ignores Z0
Awarded Mar 17 at 11:18
How to tell if I have TMC2208 or A4988 Drivers on Creality Silent V4.2.3 Board?
Awarded Mar 15 at 21:35
Is there a method for telling how much filament is left on a spool?
Awarded Mar 5 at 16:17
Over extruding and feeding gear is grinding Ender 3 pro
Awarded Feb 28 at 19:11
Ender 3 doesn't extrude enough?
Awarded Feb 28 at 13:27
How do I fill missing corners in Cura
Awarded Feb 25 at 3:33
What can cause Z height loss in the first few layers?
Awarded Feb 24 at 19:04
How do you make a new CR-10 Smart do auto bed-levelling?
Awarded Feb 23 at 12:35
Ender 5 Plus - does not level, the Z axis goes down, always
Awarded Feb 23 at 5:48
Ender 3 doesn't extrude enough?
Awarded Feb 21 at 15:25
How Do I Determine The Appropriate Magnet Strength For A Tight Seal On A Box
Awarded Feb 21 at 13:02
PLA not sticking to the build plate
Awarded Feb 19 at 22:25
OpenSCAD can't render union of two polyhedrons, but can preview just fine
Awarded Feb 18 at 6:56
Ender 5 with 8-bit Creality 1.1.4 board- Issue with speed of extruder motor spinning too slow
Awarded Feb 15 at 8:20
Cooling fan noise when head is moving in the X axis
Awarded Feb 9 at 23:16
What techniques are needed to minimise layer separation after filament change?
Awarded Feb 7 at 20:12
Problems with stock gear with no screw on Ender 3 pro
Awarded Feb 4 at 15:31
Fusion 360 + Snapmaker original for printing
Awarded Feb 3 at 9:25
Can I print and sell 3D models licensed under CC BY-NC-SA 3.0
Awarded Jan 24 at 19:26
PLA chemical resistances? Especially HCl, other acids
Awarded Jan 20 at 15:05
Printer crashed into model
Awarded Jan 19 at 12:36
Creality Ender 3 Pro - Z travel issue with TH3D firmware
Awarded Jan 14 at 16:36
Unusual printing after upgrading
Awarded Jan 13 at 21:12
My FlashForge Creator Pro has started to spontaneously restart mid-print, begin vibrating, printing along one axis repeatedly, etc
Awarded Jan 12 at 0:04
3D Printing with malicious intent
Awarded Jan 11 at 11:48
Y-axis on KP3S Kingroon only moves in one direction
Awarded Jan 10 at 12:42
Ender 3 Pro extruder motor failing constantly
Awarded Jan 7 at 3:42
Ender 3 v2 BLTouch pushing too far in X axis
Awarded Jan 5 at 18:17
What is the operator precedence in OpenSCAD?
Awarded Jan 4 at 14:12
How do I fill missing corners in Cura
Awarded Jan 4 at 12:18
Some problems with printing on my Ender 3
Awarded Dec 31, 2021 at 20:57
Ender 5 (Plus) - Gantry not square to frame, how to fix?
Awarded Dec 29, 2021 at 23:05
Dual Z-axis has different speeds (out of sync)
Awarded Dec 28, 2021 at 12:41
The BLTouch is hitting the bed on the double-probing
Awarded Dec 20, 2021 at 14:42
Ender 3 board 4.2.2 BLTouch 3.1 crashes into bed during autoleveling
Awarded Dec 20, 2021 at 8:55
1
2 3 4 5
…
24

Your privacy

By clicking “Accept all cookies”, you agree Stack Exchange can store cookies on your device and disclose information in accordance with our Cookie Policy.