Skip to main content
3D Printing

Student

 Student
First question with score of 1 or more.
Awarded 2980 times.
Crafting Perspex
Awarded yesterday
Is it viable to link stepper motor direction pins?
Awarded Sep 2 at 22:26
Negative extrusion at an angle >90 degrees
Awarded Aug 24 at 20:17
Can slicers combine vase mode and non-vase mode in the same print?
Awarded Aug 23 at 11:57
I accidentally threw away my 4th 3D Printing bed gear on my Creality Ender Pro 3, what can I use instead?
Awarded Aug 18 at 19:45
Mounting a 10 W laser on Geeetech Prusa I3 Pro B?
Awarded Aug 13 at 18:21
How should this print-in-place hinge be printed?
Awarded Aug 5 at 12:08
Why does my Labists X1 mini printer float 1 cm above the bed even after homing it?
Awarded Jul 31 at 7:25
BLTouch probing in mid air [duplicate]
Awarded Jul 29 at 13:31
Increase of filament diameter near nozzle when printing long time
Awarded Jul 26 at 6:16
Lots of issues while trying to achieve higher temperatures
Awarded Jul 25 at 21:12
Failing Print on Kobra Max-2
Awarded Jul 25 at 8:12
BLTouch problem with pin deployment
Awarded Jul 21 at 7:20
Creality K1 Max Filament Won't Feed
Awarded Jul 21 at 6:30
Printing more heat resistant materials or increasing melting point
Awarded Jul 19 at 15:40
Why is my Ender 3 nozzle z-axis raising before printing?
Awarded Jul 18 at 15:08
What would cause my 3D printer to start printing badly from one day to the other?
Awarded Jul 18 at 14:51
3D Print showing strings
Awarded Jul 14 at 10:27
How to deal with ASA warping?
Awarded Jul 13 at 15:06
Getting "heater bed not heating at expected rate" error when trying to print PETG on a glass bed
Awarded Jul 11 at 22:16
OpenSCAD hole is closed on the inside when in slicer
Awarded Jul 11 at 6:39
Hot end cooling fan runs when bed heater activated. Was expecting fan to run when hot end heater activated
Awarded Jul 10 at 6:08
How can I change the bed temperature after 3-4 layers instead of first layer?
Awarded Jul 6 at 18:12
Anet stepper (42SHDC3025-24B) pinout?
Awarded Jul 5 at 9:55
BIQU B1 ignores Z limit switch when homing
Awarded Jul 2 at 21:21
Feasibility of using prebuilt support structures
Awarded Jul 1 at 10:31
(post deleted or otherwise unavailable)
Awarded Jul 1 at 10:06
Temperature is showing without any thermistor connected
Awarded Jun 22 at 22:04
OpenSCAD import dpi setting
Awarded Jun 20 at 18:41
Can I print and sell 3D models licensed under CC BY-SA?
Awarded Jun 20 at 13:50
what is the most economical way to design a small & simple box? [closed]
Awarded Jun 20 at 13:50
What is an effective option to protect filament against moisture?
Awarded Jun 9 at 13:40
Burnt PETG extrusions
Awarded May 28 at 3:40
How would you connect multiple large prints permanently together?
Awarded May 26 at 6:35
Is the Bambu Lidar a structured light camera?
Awarded May 26 at 6:22
Proper use of filament dryer
Awarded May 23 at 0:48
Anycubic X extruder dripping brown sludge
Awarded May 21 at 20:47
Printer prints only candy floss
Awarded May 21 at 20:42
How can I avoid objects merging when exporting with Tinkercad?
Awarded May 16 at 6:34
Prints printing to the right of the bed after the firmware change
Awarded May 16 at 6:34
Font suitable for 3D printing [closed]
Awarded May 13 at 16:18
Lightweight-PLA (LW-PLA)
Awarded May 11 at 23:07
Is a damaged print bed what is causing my prints to fail?
Awarded May 11 at 13:58
First layer is thin with voids in the first corner of a rectangular object inside border
Awarded May 9 at 20:06
Modifying internal objects of models in an existing STL file
Awarded May 9 at 19:41
Help troubleshooting clogging issue
Awarded May 8 at 20:18
How to properly measure sizes of models in Blender?
Awarded May 6 at 16:47
Emboss STL from SVG
Awarded Apr 25 at 10:15
Ender 3 printer shutting down with "MAXTEMP BED" error
Awarded Apr 17 at 11:25
How strong should NEMA17 motors be?
Awarded Apr 16 at 9:58
What causes a print to be more or less "shiny"?
Awarded Apr 16 at 3:07
ender 3 repeated power outage issue
Awarded Apr 16 at 3:07
Why do hotends have heat sinks?
Awarded Apr 14 at 15:33
Gaps in print bed
Awarded Apr 13 at 13:26
G-code for stationary extrusion
Awarded Apr 5 at 11:27
Can RAMPS V1.4 with DRV8825 drivers run 10 motors?
Awarded Apr 5 at 3:50
At what bed temperature is it safe to remove PLA prints?
Awarded Mar 31 at 16:04
Using dual Y stepper drivers on Marlin / RAMPS 1.4
Awarded Mar 29 at 20:22
How can I create a mold for an atypical shape for 3D printing using Fusion 360?
Awarded Mar 28 at 3:25
LCD/DLP resin curing system
Awarded Mar 26 at 7:02
1
2 3 4 5
…
50