1
$\begingroup$

I recently installed Marlin 1.1.9.1 onto my Creality CR-10S. After doing so, the temperatures for both the bed and hotend now read -14 °C. I have changed the setting in the Marlin configurations.h to several different thermistors, and it either reads 0 or -14 °C.

I have now installed several different versions of Marlin and with each one I experience the same problem.

Is there some tuning setting that I am missing or has installing the firmware somehow fried something on my board?

$\endgroup$
2
$\begingroup$

Okay, to anyone who is looking at this post, I am an idiot. I have spent the last 4 or more hours sifting through youtube videos and forum posts to figure out this problem. I have reinstalled firmware modifications dozens of times. All of this, to just now discover that I never had the bed or hotend cables connected. That's right, I never even considered the fact that I had yet to plug in those cables after transporting my printer to a new location.

Don't be like me. Check the simplest solutions first.

$\endgroup$
1
  • $\begingroup$ MINTEMP! no connection is Mintemp -14! $\endgroup$
    – Trish
    Mar 7 at 1:41
-1
$\begingroup$

If all cabling is correct, you have most likely chosen the wrong thermosensor type. You need to put the correct temperature table for your thermosensor into your Firmware. As explained here, you need to set the number at the end of these lines to match what you have installed. The "standard" CR-10 should use the Sensor type 1: 100k/4.7 k EPCOS.

* :{ '0': "Not used", '1':"100k / 4.7k - EPCOS", '2':"200k / 4.7k - ATC Semitec 204GT-2", '3':"Mendel-parts / 4.7k", '4':"10k !! do not use for a hotend. Bad resolution at high temp. !!", '5':"100K / 4.7k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '501':"100K Zonestar (Tronxy X3A)", '6':"100k / 4.7k EPCOS - Not as accurate as Table 1", '7':"100k / 4.7k Honeywell 135-104LAG-J01", '8':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT", '9':"100k / 4.7k GE Sensing AL03006-58.2K-97-G1", '10':"100k / 4.7k RS 198-961", '11':"100k / 4.7k beta 3950 1%", '12':"100k / 4.7k 0603 SMD Vishay NTCS0603E3104FXT (calibrated for Makibox hot bed)", '13':"100k Hisens 3950  1% up to 300°C for hotend 'Simple ONE ' & hotend 'All In ONE'", '20':"PT100 (Ultimainboard V2.x)", '51':"100k / 1k - EPCOS", '52':"200k / 1k - ATC Semitec 204GT-2", '55':"100k / 1k - ATC Semitec 104GT-2 (Used in ParCan & J-Head)", '60':"100k Maker's Tool Works Kapton Bed Thermistor beta=3950", '66':"Dyze Design 4.7M High Temperature thermistor", '70':"the 100K thermistor found in the bq Hephestos 2", '71':"100k / 4.7k Honeywell 135-104LAF-J01", '147':"Pt100 / 4.7k", '1047':"Pt1000 / 4.7k", '110':"Pt100 / 1k (non-standard)", '1010':"Pt1000 / 1k (non standard)", '-4':"Thermocouple + AD8495", '-3':"Thermocouple + MAX31855 (only for sensor 0)", '-2':"Thermocouple + MAX6675 (only for sensor 0)", '-1':"Thermocouple + AD595",'998':"Dummy 1", '999':"Dummy 2" }
*/
#define TEMP_SENSOR_0 1
[...]
#define TEMP_SENSOR_BED 1
$\endgroup$
1
  • $\begingroup$ I have selected the standard sensor in the firmware as you have shown here. My results remain the same. I still get -14 degrees for all the sensors. $\endgroup$ Mar 6 at 22:17

Your Answer

By clicking “Post Your Answer”, you agree to our terms of service, privacy policy and cookie policy

Not the answer you're looking for? Browse other questions tagged or ask your own question.