Linked Questions

9
votes
3answers
102k views

Recalibrating Home-position

I got myself the Ender 3. The Home position is about 1 mm left and 2 mm in front of the front left corner. Now, the hotend center axis is 11 mm from the carrier plate with the "Mk 10" cooler ...
16
votes
2answers
26k views

What is Thermal Runaway Protection?

What is Thermal Runaway Protection (TRP) and why should I enable it? How does one do so in Marlin?
11
votes
3answers
61k views

Ender 3 nozzle homes off the bed in the Y axis

I just received my new Creality Ender 3. I was going through and checking/adjusting everything for alignment, and I noticed that when you "auto home" the print head, the nozzle stops off the ...
12
votes
2answers
9k views

What is a printer console/terminal?

I read that G-code commands can be sent through a console/terminal over USB. What is a console/terminal and how do you use that?
4
votes
2answers
31k views

Creality Ender 3 - printing in front of the build plate

I am trying to print my first test but my Creality Ender 3 starts printing near the front edge and within 10 seconds is printing in front of the tray (off onto my table). I really think it should be ...
4
votes
1answer
38k views

How to set the boundaries for BLTouch probing

I have just installed the BLTouch on my Ender 3 running Marlin 1.1.9 and I want to set it up so the probing does the 9 points in a perimeter that uses most of the bed surface area. At the moment the ...
6
votes
2answers
9k views

Nozzle jumps off the bed when using Marlin Mesh Bed Leveling

I am using Marlin firmware with a RAMPS board on an Anet A8 printer. The bed size for the printer is 220 x 220 mm and that is stated in the configuration.h file. ...
1
vote
1answer
13k views

Updating Marlin Firmware - Step by Step Guide

Note: This question is meant as a wiki to include all steps that are needed to update your printer with a self configured Marlin firmware version. The answer is a wiki that is currently in development ...
6
votes
1answer
7k views

Setting custom x/y bed bounds for Anet A8/marlin

I have an Anet A8 that I just flashed with the latest Marlin firmware (1.1.9). I'm sending prints to my printer with Ultimaker Cura via OctoPrint. I have affixed a PEI surface to my bed that's about ...
5
votes
2answers
5k views

Extruder drive cog slipping on filament

I've been printing PLA on a Pegasus 12" for 2 years. Print quality has been great but in the last few months the quality of the prints has deteriorated. After looking into it, it seems when the head ...
4
votes
2answers
9k views

Ender 3 homing problem

I got myself a Creality Ender 3 and just finished assembling it and I noticed that the home position is at the right instead of the left. It also is about about 3 mm in front of the right corner. ...
1
vote
2answers
1k views

Using maximum width when slicing in Ultimaker Cura

I am trying to slice a model that is half a mm less than max width, but not successful. What am I missing? Is there some minimum value less than maximum allowed, or something? Edit: after changing ...
3
votes
1answer
6k views

Bed size and nozzle homing offset in Marlin 1.1.9 firmware

This is driving me up the wall, hope somebody can give me some advice... I have an Anet A8 (metal frame, so 'AM8'). Bed is the original 220x220 mm. When the nozzle is at the X/Y end stops it ...
0
votes
1answer
5k views

How to set Home Offsets and Manual Home definitions in Marlin correctly? [duplicate]

I am using an Ender 3 and I have just upgraded to the Hero Me Gen 5 fan duct adapter. This has shifted the nozzle position. I also flashed some new Marlin 2 firmware and in the Hero Me manual it says ...
5
votes
1answer
975 views

How to line up (x,y) print area between hardware and software?

I'm trying to line up the physical print bed of my printer (Printrbot Simple Metal) to the virtual print area of the slicer (Cura). So far, they've never been properly aligned. It was never that big ...

15 30 50 per page