Linked Questions

1
vote
1answer
2k views

Automatic bed leveling probes outside of bed despite NOZZLE_TO_PROBE_OFFSET [duplicate]

I just changed the motherboard of my CR-10 mini printer to an SKR 1.4 and installed Marlin 2.0.x on it. Everything seems to work except for the automatic bed leveling. I’m using an EZABL probe. The ...
0
votes
0answers
30 views

Printer places prints off the bed after change in bed Z-probe area settings [duplicate]

I really don't know what I am doing wrong. Since changing my bed level sensor from left of the extruder to back mount, it doesn't work proper anymore and I have some fundamental thing I don´t ...
7
votes
3answers
11k views

How to offset my probe so it's not hanging off the bed at 0, 0 position when printing

I had my printer printing fine when using the stock trigger switch as I used it to print the green bracket you see in the picture. My problem now is when I do a print with the sensor, it moves to 0,...
6
votes
2answers
9k views

Nozzle jumps off the bed when using Marlin Mesh Bed Leveling

I am using Marlin firmware with a RAMPS board on an Anet A8 printer. The bed size for the printer is 220 x 220 mm and that is stated in the configuration.h file. ...
1
vote
1answer
13k views

Updating Marlin Firmware - Step by Step Guide

Note: This question is meant as a wiki to include all steps that are needed to update your printer with a self configured Marlin firmware version. The answer is a wiki that is currently in development ...
7
votes
1answer
4k views

Issues with Auto Bed Leveling

I have enabled auto bed leveling on my 3D printer. I have used a 6-36 V inductive sensor with a 7805 voltage regulator running the sensor at 10.78 V. I am using Marlin 1.1.9. This is my configuration ...
3
votes
1answer
11k views

Where to define grid for bilinear levelling in Marlin

I'm using firmware Marlin 2.0.3 on an Anet A8 printer. I'm using a Roko SN04-N NPN bed leveller. I've managed to set up 3 points bed levelling but I wanted to try the bilinear levelling. Issue is, ...
4
votes
1answer
2k views

ANet A8 running Marlin v1.1.9 Auto Bedlevel with ROKO SN04-N

I'm trying to get the ROKO (SN04-N) sensor to work with my Anet A8. First of all, while trying to screw it to the extruder, I tightened it too much and sort of broke the acrylic plate... sort of. I ...
0
votes
0answers
3k views

Ender 5 Plus offset issue

Me: Experienced coder, Entry level 3D print person. Setup Ender 5 Plus Creality V2.2 Board BLTouch Marlin Titan Aero Notes: Using a custom mount for the head and probe. Front Left Top is 0,0,0 X/Y ...
2
votes
1answer
2k views

BLTouch missing build plate on levelling

I have finally sorted the problems out with the frozen screen, but inevitably there's always more to take there place. I have installed the latest version of the 'Tiny Machines' Firmware but on ...
1
vote
1answer
1k views

Switch nozzle contact probe auto leveling with Marlin 2.0

I have a Robo R1+ which uses the nozzle contacting the glass print bed to level the printer. When the print head strikes the bed the Z-min endstops open signaling that the bed is touched. I recently ...
1
vote
1answer
1k views

G29 Bed Level not doing anything on Marlin 2.0

I've just updated my Anet A8 with the blue bed level sensor to Marlin 2.0 . Both pressing the Level Bed button on the display or using G29 after ...
0
votes
1answer
964 views

UBL Marlin settings to cover whole bed

This question is related to: How to set Z-probe boundary limits in firmware when using automatic bed leveling? I am trying to figure out how to set UBL In Marlin to cover as much bed as possible. So ...
3
votes
1answer
736 views

Printer goes beyond the bed when auto leveling

I am trying to add auto bed leveling to my Prusa i3. When I run G28 my printer hits the X and Y end stops properly, then it assumes X=25, Y=99 position on the bed ...
2
votes
0answers
414 views

Adjust Y axis only for Octoprint Bed Visualizer

I am using the Octoprint Bed Visualizer on my Ender 3/BLTouch setup. When it moves to the front left corner, the BLTouch sensor nearly misses the bed touching the very edge. Likewise, it is shifted ...

15 30 50 per page