Linked Questions

7
votes
2answers
6k views

Are silicone socks safe?

It's fairly common for E3D to sell silicone socks for their hot ends. There are also other companies that sell these silicone socks for their hot end cartridges. According to a brief internet search, ...
9
votes
2answers
23k views

How to center my prints on the build platform? (Re-calibrate homing offset)

When I print large prints close to (but not exceeding) the maximum dimensions of the heated build platform on my Anet A8, the brim or skirt or the print itself is printed outside the heated bed, while ...
1
vote
1answer
7k views

How to activate Power Loss Recovery in Marlin?

Standard Marlin has one problem: when the power suddenly is gone, the print is gone. Prusa and many china printers however come with "Power Loss Recovery" or "Power Out Protection" or similar. But ...
6
votes
1answer
2k views

How to set up Marlin to use a heated chamber?

I have an infrared lamp I'd like to use to heat my chamber. Right now I don't have plans to install a cooling fan, but I will if I need to. This question pertains to Marlin (2.0, preferably) in ...
3
votes
2answers
1k views

How to repair burnt heat bed connector?

My Anet A8 suddenly had issues with being unable to heat the bed. After ruling out software issues, I disconnected the connector and found this (sorry for the terrible quality): The left most pin on ...
4
votes
1answer
1k views

Are there printers that don't have thermal runaway protection?

This question asks about the reasoning behind thermal runaway protection and how to turn it on. However, how do I know if my printer does not have protection in the first place? Either because it is ...
1
vote
1answer
2k views

Updating Marlin Firmware - Step by Step Guide

Note: This question is meant as a wiki to include all steps that are needed to update your printer with a self configured Marlin firmware version. The answer is a wiki that is currently in development ...
3
votes
4answers
663 views

Anet A8 ignores extruder temperature?

I don't understand what's wrong with my G-code. I have set the printing temperature to 195 °C but when I try to print, the target temperature is always 0 °C and printing never starts. I ...
5
votes
1answer
642 views

Thermal runaway on extruder hotend

I am getting thermal runaway even after PID autotunning many times. I tried 10, 15, 20, 25 and 30 cycles and after reuploading FW onto the printer but I still get the error... I've built a copy of ...
4
votes
1answer
628 views

Thermal runaway with specific prints

I have been experimenting with PETG on my CR-10 upgraded with an E3D all-metal hot end and Marlin firmware on the controller. I am printing with 0.8 mm nozzle at 250 °C and an 85 &...
1
vote
2answers
795 views

M502 will reset all configurable settings to their “factory defaults”, which settings are those?

From the M502 documentation page can be read that M502: Reset all configurable settings to their factory defaults. Please ...
3
votes
2answers
459 views

Anet A8 Wrong Hotend Temp

My Anet A8 reads as 120ish degrees Celsius, but it is set to 200 degrees. I don't know if it is reading the wrong temperature because it still pushes out plastic when I force it. It will climb up and ...
1
vote
2answers
174 views

Hotend doesn't maintain temperature

I got an Anycubic Predator last month, and after resolving a few mechanical problems, I was able to get it printing decently well. The only significant modification I've made so far is a set of 8-...
0
votes
1answer
22 views

Extruder increase temperature

I bought a month ago the Artillery Genius. Everything was pretty good until today, I was printing a test cube and it stopped pulling out filament, when I looked the temperature it was -15 °C, a few ...