Linked Questions

1
vote
1answer
67 views

Figure out max bed temperature

I have a Tronxy X8 (yes, I know, poor choice but I didn't know better) and after some years printing PLA, PETG and TPU, I am considering trying ABS, since I got myself a second hotend which can go up ...
1
vote
1answer
243 views

FlashForge Finder turns off mid print and is unable to reset or update firmware

I am new to 3D printing and am trying to get started with a FlashForge Finder. Unfortunately, the printer keeps shutting off mid print, and I am unable to find a cause. Here's what I have tried thus ...
3
votes
2answers
8k views

How do I set the flow rate on my Ender 3 Pro and have it stay at that percentage?

I am trying to increase the flow rate on my Ender 3 from 100 to 108 % but every time I start a new print it reverts back to the old 100 % flow rate. I have clicked through the settings and pressed the ...
1
vote
1answer
41 views

Random hot-end temperature spikes

I've been having issues with thermal runaways lately due to random temperature spikes on my Ender 3. I figured it was out of calibration so I did a PID tune and still had issues. I then replaced the ...
1
vote
0answers
18 views

Ender 3 V2 hotend temperature issues [duplicate]

Recently, I started experimenting with new filaments on my Ender 3 V2. I got a spool from here. This is PETG filament and I started dialing in the temperature to run a smooth print. I found on my V2, ...
11
votes
2answers
51k views

How to center my prints on the build platform? (Re-calibrate homing offset)

When I print large prints close to (but not exceeding) the maximum dimensions of the heated build platform on my Anet A8, the brim or skirt or the print itself is printed outside the heated bed, while ...
0
votes
2answers
3k views

"Err: MAXTEMP: E1" when THERMAL_PROTECTION_HOTENDS is disabled

I am trying to port Marlin to my Qidi Tech 1 printer which previously ran Sailfish 7.8. Everything worked fine on the old board, including the temperature sensors. All cables except for power, LCD, ...
0
votes
0answers
42 views

CR-10 S Pro bed heating problems

I've had my bed continually heat up and not stop. I have replaced the SSR and replaced it with an identical-looking one and also replaced it with a MOSFET.
0
votes
2answers
48 views

Long Print with Lotmaxx SC-10

I am trying to print something that might take 15 hours. I don't want to risk my printer so if I print for 15 hours, what is the worst that can happen? So far, I haven't printed anything for more than ...
3
votes
5answers
1k views

Anet A8 ignores extruder temperature?

I don't understand what's wrong with my G-code. I have set the printing temperature to 195 °C but when I try to print, the target temperature is always 0 °C and printing never starts. I have tried ...
0
votes
1answer
60 views

Extruder increase temperature

I bought a month ago the Artillery Genius. Everything was pretty good until today, I was printing a test cube and it stopped pulling out filament, when I looked the temperature it was -15 °C, a few ...
8
votes
2answers
7k views

Are silicone socks safe?

It's fairly common for E3D to sell silicone socks for their hot ends. There are also other companies that sell these silicone socks for their hot end cartridges. According to a brief internet search, ...
1
vote
1answer
13k views

Updating Marlin Firmware - Step by Step Guide

Note: This question is meant as a wiki to include all steps that are needed to update your printer with a self configured Marlin firmware version. The answer is a wiki that is currently in development ...
1
vote
2answers
1k views

Hotend doesn't maintain temperature

I got an Anycubic Predator last month, and after resolving a few mechanical problems, I was able to get it printing decently well. The only significant modification I've made so far is a set of 8-...
1
vote
2answers
3k views

M502 will reset all configurable settings to their "factory defaults", which settings are those?

From the M502 documentation page can be read that M502: Reset all configurable settings to their factory defaults. Please ...

15 30 50 per page