Linked Questions

1
vote
2answers
3k views

M502 will reset all configurable settings to their "factory defaults", which settings are those?

From the M502 documentation page can be read that M502: Reset all configurable settings to their factory defaults. Please ...
0
votes
2answers
47 views

Long Print with Lotmaxx SC-10

I am trying to print something that might take 15 hours. I don't want to risk my printer so if I print for 15 hours, what is the worst that can happen? So far, I haven't printed anything for more than ...
0
votes
2answers
3k views

"Err: MAXTEMP: E1" when THERMAL_PROTECTION_HOTENDS is disabled

I am trying to port Marlin to my Qidi Tech 1 printer which previously ran Sailfish 7.8. Everything worked fine on the old board, including the temperature sensors. All cables except for power, LCD, ...
6
votes
1answer
6k views

How to set up Marlin to use a heated chamber?

I have an infrared lamp I'd like to use to heat my chamber. Right now I don't have plans to install a cooling fan, but I will if I need to. This question pertains to Marlin (2.0, preferably) in ...
5
votes
1answer
1k views

Thermal runaway on extruder hotend

I am getting thermal runaway even after PID autotunning many times. I tried 10, 15, 20, 25 and 30 cycles and after reuploading FW onto the printer but I still get the error... I've built a copy of ...
4
votes
1answer
2k views

Thermal runaway with specific prints

I have been experimenting with PETG on my CR-10 upgraded with an E3D all-metal hot end and Marlin firmware on the controller. I am printing with 0.8 mm nozzle at 250 °C and an 85 &...
4
votes
1answer
1k views

Are there printers that don't have thermal runaway protection?

This question asks about the reasoning behind thermal runaway protection and how to turn it on. However, how do I know if my printer does not have protection in the first place? Either because it is ...
1
vote
1answer
67 views

Figure out max bed temperature

I have a Tronxy X8 (yes, I know, poor choice but I didn't know better) and after some years printing PLA, PETG and TPU, I am considering trying ABS, since I got myself a second hotend which can go up ...
1
vote
1answer
41 views

Random hot-end temperature spikes

I've been having issues with thermal runaways lately due to random temperature spikes on my Ender 3. I figured it was out of calibration so I did a PID tune and still had issues. I then replaced the ...
1
vote
1answer
243 views

FlashForge Finder turns off mid print and is unable to reset or update firmware

I am new to 3D printing and am trying to get started with a FlashForge Finder. Unfortunately, the printer keeps shutting off mid print, and I am unable to find a cause. Here's what I have tried thus ...
1
vote
1answer
13k views

Updating Marlin Firmware - Step by Step Guide

Note: This question is meant as a wiki to include all steps that are needed to update your printer with a self configured Marlin firmware version. The answer is a wiki that is currently in development ...
1
vote
1answer
15k views

How to activate Power Loss Recovery in Marlin?

Standard Marlin has one problem: when the power suddenly is gone, the print is gone. Prusa and many china printers however come with "Power Loss Recovery" or "Power Out Protection" or similar. But ...
0
votes
1answer
60 views

Extruder increase temperature

I bought a month ago the Artillery Genius. Everything was pretty good until today, I was printing a test cube and it stopped pulling out filament, when I looked the temperature it was -15 °C, a few ...
1
vote
0answers
18 views

Ender 3 V2 hotend temperature issues [duplicate]

Recently, I started experimenting with new filaments on my Ender 3 V2. I got a spool from here. This is PETG filament and I started dialing in the temperature to run a smooth print. I found on my V2, ...
0
votes
0answers
41 views

CR-10 S Pro bed heating problems

I've had my bed continually heat up and not stop. I have replaced the SSR and replaced it with an identical-looking one and also replaced it with a MOSFET.

15 30 50 per page