Questions tagged [anet-a8]

This tag should be used for specific questions about specific issues for the Anet A8 printers.

13 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
0answers
40 views

Bioprinter does not extrude Anet A8 Marlin

I have a modified Anet A8 that is supposed to print hydrogels (paper : Ultra-Low-Cost 3D Bioprinting, Kahl M et al. 2019). For this to work, we do not need any temperature-related settings, however, I ...
1
vote
0answers
24 views

Odd behaviour of steady feedrate increase

For some weeks I noticed really odd behaviour on my OctoPi controlled Anet A8. I'm using an MKS Gen L board with TMC2208 on this and constellation worked for a year now. When starting a print, I ...
1
vote
1answer
40 views

3 Extruders on SKR V1.1, how set up 2 in 1 out (Y piece), and 1 single extruder in latest Marlin?

On Anet A8 with SKR V1.1 32 bit board my intention is to use 3 extruders on my Anet A8, 1+2 via Y-piece on single nozzle, 3rd Extruder with 2nd nozzle. Need another stepper to connect to SKR V1.1 (10 ...
1
vote
0answers
102 views

Filament getting stuck after 1.5 hours of printing

Problem: After about 1.5 hours of printing on my modified Anet A8 the (converted to Bowden) extruder begins to make a clicking noise. The filament is not being pushed through the hotend (E3D V6, it is ...
1
vote
2answers
897 views

Nozzle goes down after bed leveling BLTouch

I am new and I really hope you could help me out. I have two printers, one is an Anet A8 and the other one is a CreatBot DX plus. On both of them I installed a BLTouch, firstly on the DX and today on ...
1
vote
0answers
58 views

How to avoid line curvature in first layer of a 3D print

I have a problem with large lines in the first layer of my prints which have curvatures. The last layer has no problems. You can see the problem in the horizontal line of the "A", the rest of the "A" ...
1
vote
0answers
138 views

PyCNC - How to configure for my setup?

I have replaced the main board of my Anet A8 printer with a Raspberry Pi based one, running PyCNC. After many issues I have finally got to a point where all the motors work as well as heating and ...
0
votes
0answers
26 views

Anet A8 BLTouch bed leveling starts outside of bed

I just upgraded Anet A8 to Marlin 2.0.x with BLTouch, but my issue is when I press bed level the center is not correct, and when it goes to the first point it is outside of the bed. My BLTouch is back ...
0
votes
0answers
27 views

Heating problems on Anet A8

I've set the bed temperature to 60 °C, but it goes to 39 °C and stops heating up. I've set the hotend temperature to 190 °C, but it goes to 300 °C. Then DEF both of them
0
votes
0answers
42 views

Got "Heating failed" error while heat catridge is working

I bought an Anet A8 Plus in January. Everything worked pretty well until one week ago. When I tried to print something, I got a "Heating Failed" error, as the hotend didn't get hot. I've ...
0
votes
0answers
56 views

Anet A8 moves down into piece, destroying it, just before the printer is set to finish

I hope someone can help me figure out what's going on with my printer. I have been printing a couple of pieces and it's been printing perfectly. But for some reason every now and then, the printer ...
0
votes
0answers
56 views

PyCNC - Z steppers screaming

I'm transforming my Anet A8 printer to Raspberry Pi driven using PyCNC. Things seem to look promising so far apart from the Z motor doing nothing but making screaming-like sound when supposed to be ...
0
votes
0answers
273 views

Vibration marks when printing slowly on Y-axis

My Anet A8 prints come out with vibration marks when I print under 80 mm/s. Above that value, it's fine. Has anyone experienced something like this with any axis? The Y-axis motor also ...