Questions tagged [anet-a8]

This tag should be used for specific questions about specific issues for the Anet A8 printers.

Filter by
Sorted by
Tagged with
1
vote
0answers
123 views

PyCNC - How to configure for my setup?

I have replaced the main board of my Anet A8 printer with a Raspberry Pi based one, running PyCNC. After many issues I have finally got to a point where all the motors work as well as heating and ...
0
votes
1answer
159 views

Anet A8 stock replacement fuse between motherboard and PSU

My inline fuse burned and I don't know how many ampere the new fuse should have.
0
votes
1answer
861 views

Z-axis of Anet A8 always moves additional 5 mm upwards when moving X and Y-axis in Ultimaker Cura

I have an Anet A8 using the Marlin 1.1.8 Firmware. There are two (very much related) things that bother me: G00 Z0 (after auto home from printer menu which ...
0
votes
1answer
175 views

Y Axis motor is really loud

The Y-axis motor is really loud. The pitch of the sound varies depending the angle of the motor (in some angles the motor is silent, in others it's louder than a fan). I am looking for a solution ...
0
votes
1answer
815 views

Anet A8 display on MKS Gen L board [duplicate]

So I have read this question, Connecting (Anet A8) 2004 display to MKS GEN L. That looked so easy, so I rewired the connectors and switched the VCC and GND pins. In the Marlin firmware I disabled ...
0
votes
0answers
13 views

Anet A8 BLTouch bed leveling starts outside of bed

I just upgraded Anet A8 to Marlin 2.0.x with BLTouch, but my issue is when I press bed level the center is not correct, and when it goes to the first point it is outside of the bed. My BLTouch is back ...
0
votes
0answers
27 views

Heating problems on Anet A8

I've set the bed temperature to 60 °C, but it goes to 39 °C and stops heating up. I've set the hotend temperature to 190 °C, but it goes to 300 °C. Then DEF both of them
0
votes
0answers
32 views

Got “Heating failed” error while heat catridge is working

I bought an Anet A8 Plus in January. Everything worked pretty well until one week ago. When I tried to print something, I got a "Heating Failed" error, as the hotend didn't get hot. I've ...
0
votes
0answers
53 views

Anet A8 moves down into piece, destroying it, just before the printer is set to finish

I hope someone can help me figure out what's going on with my printer. I have been printing a couple of pieces and it's been printing perfectly. But for some reason every now and then, the printer ...
0
votes
1answer
54 views

3d printer recommendations that can print fidgets? [closed]

I am looking for a cheap 3d printer that can print this: https://www.thingiverse.com/thing:1307100 and is hopefully under US $200, such as the Creality Ender 3, Monoprice Select Mini Pro and V2, the ...
0
votes
2answers
761 views

Nozzle goes down after bed leveling BLTouch

I am new and I really hope you could help me out. I have two printers, one is an Anet A8 and the other one is a CreatBot DX plus. On both of them I installed a BLTouch, firstly on the DX and today on ...
0
votes
0answers
49 views

PyCNC - Z steppers screaming

I'm transforming my Anet A8 printer to Raspberry Pi driven using PyCNC. Things seem to look promising so far apart from the Z motor doing nothing but making screaming-like sound when supposed to be ...
0
votes
0answers
260 views

Vibration marks when printing slowly on Y-axis

My Anet A8 prints come out with vibration marks when I print under 80 mm/s. Above that value, it's fine. Has anyone experienced something like this with any axis? The Y-axis motor also ...

1 2
3