Questions tagged [bed-leveling]

Use this tag for questions regarding the manual or automatic leveling of the build platform.

44 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
7
votes
0answers
83 views

Marlin 2.0 Firmware temperature jumping on LCD when trying to configure UBL

Flashed Marlin 2.0 on my Folgertech 2020 Prusa i3 variant. Calibrating seems to have gone smoothly until I tried to set up UBL. Saved the mesh into EEPROM with the ...
5
votes
0answers
59 views

What options exist for augmenting the automatic bed-leveling?

When I print this file, one section smears. The print head is dragged through the soft filament. At first I thought my aluminum bed was warped, so I upgraded to a glass bed. Test prints were much ...
2
votes
0answers
28 views

Ender 3 V2 ignories Z-axis limit switch

My shiny new Ender 3 V2 seems to ignore the Z-axis limit switch, when I print a model. It moves the nozzle so far down, that it scratches on the bed and destroys the nozzle. However, when I use the ...
2
votes
0answers
76 views

Z homing problem; starts printing in the air

I have a DIY 3D printer with Marlin firmware. I use an LJ12A3-4-Z/BY sensor for the Z probe. Recently I have had a ridiculous problem with Z homing. In doing Z homing, it senses the bed, goes up, and ...
2
votes
0answers
245 views

BLTouch will not deploy, stow, or deploy when homing or auto leveling

So I am just about at my wit's end with these stupid BLTouch sensors - with 3 separate posts on this forum regarding them, my own posts even showing in the 'Similar questions' box at the time of ...
2
votes
0answers
41 views

CoreXY mesh probing issue

I am trying to compensate for bed leveling by measuring a mesh with my Z probe, a BLTouch, and I am unable to do so. I am using RepRap firmware version 3 and have a CoreXY printer. The first thing I ...
2
votes
0answers
107 views

BLTouch not covering the whole bed area

My problem is that the BLtouch doesn't probe the whole bed, in which the probe starts from the left edge and stops at the middle of the bed. I'm using Marlin 2 software and this the code in the ...
2
votes
0answers
94 views

Should center point of G29 matrix always be zero?

Questions: Should repeated applications of G29 (auto-level) result in the same matrix as long as nothing is loose or has otherwise mechanically changed? Should ...
2
votes
0answers
90 views

3DTouch activating but responding too late

I installed a knockoff BLTouch called the 3DTouch on my Sidewinder X1. The sensor triggers correctly, however, the printer responds to the signal way too late. For example, I was testing it and ...
2
votes
0answers
906 views

Inconsistent Auto Bed Leveling - Having To Calculate Z Offset For EVERY Print

I am having a problem with my Flying Bear P902 3D printer where I have to calculate the Z offset for every single print. I calculate it using this method (and store it in EEPROM) : Link to ...
1
vote
0answers
44 views

Tronxy X5SA not working properly after Marlin firmware installation

Yesterday I just installed Marlin firmware, 2.0.x bugfix version on my Tronxy X5SA (v6). I did it in the way explained on GitHub, with Visual Studio Code, Platform IO, Marlin auto build. I applied the ...
1
vote
0answers
26 views

Bed crashing into print head when levelling

I have been printing okay for months, but, I had an overnight print failure for the first time; so turned off the printer. Restarted it, thought I would need to level the bed. Normally when I turn on ...
1
vote
1answer
39 views

First layer inconsistency

I have been having issues on my Ender 3 v2 for a while regarding the first layer. As shown in the images, certain sections of the layer are decent while there are almost seemingly periodic points in ...
1
vote
1answer
53 views

Z-Probe height isn't working

I just upgraded my CR-10 to a 32-bit board with Marlin and a BLTouch for bed-leveling. Here is my process: Run bed-leveling and save setting to EEPROM Make sure that software end-stops are off with <...
1
vote
1answer
112 views

How to solve Ender 5+ weird Z-axis behavior issue?

Before you select if you want automatic or manual leveling, the printer runs a routine to determine the Home Z-axis at the center of the bed. This starts OK, then the level goes to maximum (of the ...
1
vote
0answers
56 views

Nozzle too high on first layer after leveling

I've had my Ender 5 Pro for 6 months now, printing happily and quite a lot. Some days ago, a print failed mid-way, and since then I've not been able to make it print properly. I've now spent days ...
1
vote
0answers
382 views

Cannot configure Marlin 2/0.X bugfix on Ender 5 pro, 4.2.7 board with BLTouch 3.1

I am new to 3D printing and recently purchased a Ender 5 Pro. I came and the 8 bit 1.15 board was broken (couldn't run extruder). I upgraded to a 32 bit Creality 4.2.7 and also purchased a BLtouch 3.1 ...
1
vote
1answer
103 views

Bed is leveled and not warped but still uneven printing?

I have the Creality CR-10S. I replaced the glass it originally came with as it was warped and I wasn't getting any material out on 2 of the sides. I switched to a PEI sheet and got the same results ...
1
vote
1answer
220 views

Marlin firmware: move without auto bed leveling

I am working on a filament unload script. My current problem is that the script always does an auto bed leveling. I have two scripts to test this issue: ...
1
vote
1answer
427 views

How to probe twice while mesh bed leveling with a BLTouch setup

I am using an Ender 3 (v1.1.4) with Marlin 1.1.X bugfix installed. Also BLTouch v3.1 is used. The probe is deployed once only while mesh bed leveling. How can I make the probe deploy twice at every ...
1
vote
1answer
1k views

Bed probing feed rates

I was watching a friend's Prusa run the bed-probe routine and I realized how pathetically slow mine is and takes forever. I want to speed it up. What parameters in Marlin's ...
1
vote
0answers
86 views

Marlin - G92 after bed levelling?

In some of my G-code files the job X and Y start from 0, 0. I move the nozzle to where I want the print to start and then send G92 X0 Y0 Z0 to the printer and only ...
1
vote
0answers
159 views

What are pros and cons of piezo Vs strain gauges bed leveling sensors?

I'm designing a dual hotend carriage for a HEVO printer that will run in an enclosed heated chamber and I'm evaluating which bed leveling sensor I should use. I read that BLTouch and similar sensors ...
1
vote
0answers
1k views

Marlin Bed-Leveling Vs Skew Correction

I've added a G29 command in my starting script to do bed leveling process before every print. It works fine and compensates my bed during prints. But when I print larger models, they're all skewed in ...
1
vote
0answers
138 views

PL-08N inductive sensor not turning off

I have one of these inductive sensors marked as PL-08N which should work within a 4-30 VDC range and trigger at 8 mm or ...
0
votes
0answers
16 views

BLTouch goes behind print bed

I want to install Marlin 2.0 on my CR20 Pro but when I try to level the bed it goes behind the bed (in my direction on the Y axis). Here is my bed config: ...
0
votes
1answer
84 views

Weedo Tina2/Monoprice Cadet auto bed leveling: Sensor not moving down to touch the print bed

So I bought this printer three days ago as a way to dip my toes into the 3d printing world, and it was working great at first. But at some point, the ABL procedure started behaving oddly: Instead of ...
0
votes
0answers
93 views

BLTouch not levelling correctly (it does seem to work, just not accurately enough)

My setup Ender 3 Creality glass bed Creality 3D BL Touch auto bed levelling kit v1 Creality 3D silent mainboard v4.2.7 OctoPrint running on a Raspberry Pi 4 connected over USB (with the 5 V pin ...
0
votes
0answers
24 views

BLTouch problem - bed leveling

I have a problem with my Ender 3 printer with BLTouch v3.1. Firmware from this site. After assembly, firmware upload, Z-Offset setting, initial leveling of the table, the sensor works, but I can never ...
0
votes
0answers
38 views

Automatic leveling of the bed does not work

I am trying to run the G29 G-code for my 3D printer to automatically level the bed of the printer. Every time I try run the G-code my printer just beeps and nothing ...
0
votes
0answers
28 views

Different steps per unit while Z-Homing

Recently I've had some problems with my printer. My board and drivers got fried. Long story short, Now I have MKS-Gen-L v1.0 with LV8729 for X,Y,Z axes and extruder with these steps/mm: ...
0
votes
0answers
150 views

Ender 3 Pro & BLTouch clone issue

I just installed a BLTouch clone on my Ender 3 Pro with a standard 1.1.4 board. The sensor seems to work but is giving me problems. I used the Teaching Tech tutorial on YouTube to install it, but ...
0
votes
0answers
23 views

BLTouch V3 levels accurately on some parts of the bed sometimes or is widely off on others and sometimes scrapes

I'm trying out the new Ender 3 Pro, replaced the Z switch and put the BLTouch V3 in its place and when I try test prints with it after bed leveling, it sometimes print part of my bed on level, and ...
0
votes
1answer
109 views

Levelling issues with BLTouch sensor; unlevel and weak adhesion

I have a Creality CR-10 Max with BLTouch. After I have manually levelled the bed and set the BLTouch to do an auto level it seems to unlevel the bed and only prints one side of the bed. However, it’s ...
0
votes
0answers
187 views

How do I reset the bed leveling data?

I have a Creality CR-10 S5 which is using Marlin firmware 1.1.6. I recently got a level to level my printing bed, good high precision one. Afterwards it was printing as if my bed was not level. I ...
0
votes
0answers
135 views

Flow + Line Width = over / under extrusion, how does that work?

I am just trying to deeply understand relations between those parameters. I am not a noobie, but just trying to be more smart with a printer, instead of changing parameters randomly to see effects on ...
0
votes
1answer
920 views

UBL Marlin settings to cover whole bed

This question is related to: How to set Z-probe boundary limits in firmware when using automatic bed leveling? I am trying to figure out how to set UBL In Marlin to cover as much bed as possible. So ...
0
votes
0answers
478 views

Ender 3 Pro with BLTouch bed leveling stops after 1 test (Marlin 2.0.7.2)

I have an Ender 3 Pro with the BLTouch installed. Firmware is Marlin 2.0.7.2. I followed this instruction. When I start the bed leveling it will go to the center, check it twice and then return to the ...
0
votes
0answers
108 views

Marlin 1.1.9 mesh editing causes the nozzle to hit the bed and UBL is not correcting the leveling issues

ISSUE 1 The printer is having a physical bed size of 315 x 315 mm and there are 2 stepper motors that drive the extruder up and down. The 2 Z-steppers are synced and I already have a process to make ...
0
votes
0answers
145 views

Auto bed leveling with stepper motor lock

I have a botObject printer that was discontinued that I want to run using a RAMPS 1.4 board. The bed leveling was done by the print nozzle being pushed down on the spring loaded bed and then the ...
0
votes
0answers
127 views

Monoprice MP10 Mini, can't get a decent print

Update: if i press the button "Home" it will correctly posizionate the nozzle above the printing bed, with a gap wide enough to insert a sheet of paper between the nozzle and the surface. But, and ...
0
votes
1answer
250 views

First layer rippling and no filament in the certain areas

Hello I'm new to 3D printing and I noticed some problem with my print. I've print it 3 times and relevel the bed now, I found that the right lower corner always have holes, some string problem ...
0
votes
0answers
339 views

Creality Ender 3 EZABL bed levelling not working

I've been pulling my hair out for the last couple of weeks with trying to get a decent print out of my Ender 3. I recently bought this auto bed levelling kit and these solid bed mounts for my Ender 3....
0
votes
0answers
121 views

Z level babystepping works inconsistently after BLTouch was installed

After I installed the BLTouch sensor, the manual adjustment of the Z offset is unreliable. I found that for it to work, the software endstops must be disabled. If they are enabled, the nozzle won't ...