Questions tagged [bed-leveling]

Use this tag for questions regarding the manual or automatic leveling of the build platform.

Filter by
Sorted by
Tagged with
1
vote
1answer
5k views

3DTouch sensor fails after probe deployment and triggering

I'm using a 3DTouch sensor (from Geeetech) on a self-build CoreXY printer (HyperCube Evolution). The sensor worked perfectly until not being used for a month. The symptoms are that it fails to deploy ...
5
votes
1answer
477 views

Does auto leveling result in sheared prints?

I asked this question as a small question under an answer of another question (How bed leveling is achieved without table screws?), but have been asked to post this as a separate question to answer it ...
8
votes
3answers
1k views

What exactly does automatic bed leveling do?

I get the concept of automatic bed leveling...the printer moves around the bed and uses a sensor to identify high and low spots, then "software compensates for differences". But what exactly does "...
6
votes
3answers
7k views

Will a glass bed warp as it is heated?

I purchased a glass bed to use with my still-in-transit Ender 3. Since the bed came in before the printer, I pulled it out and used a flat edge ruler to see how flat the glass surface is. It appears ...
3
votes
1answer
328 views

How bed leveling is achieved without table screws?

I have seen printers with table screws and bed leveling sensor and printers that have only bed leveling sensor (such as Prusa). So my question is how does the bed levelling work when there is only a ...
4
votes
2answers
3k views

BiLinear bed leveling

My G29 command reports +0.178 +0.281 +0.830 -0.614 -0.012 +0.371 -1.208 -0.849 -0.351 So should I tighten up the screw of the bed, close to 0,0 position or ...
3
votes
1answer
719 views

Marlin Firmware Auto Leveling only re-centers the XY-axis (Delta printer)

I'm trying to get my printer to auto level its bed, with Marlin firmware using the following: Printer: Kossel Linear plus (Delta 3D printer) Board: MKS Base V1.5 Firmware: Marlin customized I go ...
5
votes
1answer
518 views

Adhesion problem (heat bed or extruder issue)

I am having an issue with the transition from the first layer to the second. It seems that the first layer isn’t staying put on the hot bed and the extruder is dragging it around creating a ball of ...
5
votes
2answers
4k views

Z-Axis zero/home position is higher than the actual print starting position

I'm having an issue with my very first printer, a Monoprice Select Mini V2. After doing about 20 successful prints on it, the Z axis is suddenly acting very odd. When I 'home' the Z axis and move the ...
5
votes
2answers
3k views

Delta printer nozzle not moving square with a perfectly level bed (as if the bed is bent… but it isn't)

I've been having this problem with my delta 3D printer where my nozzle isn't moving flat with my print bed (as if the bed is bent) but I have used the edge of my steel ruler and it seems to be ...
5
votes
1answer
10k views

Adding extra Z-offset to bed for PETG in Slic3r

Having printed exclusively in PLA for the past year, I'm now looking at trying out PETG in order to print a set of spare parts for my new Prusa i3 mk3. I have bought a roll of PETG from Rigid.ink and ...
7
votes
2answers
21k views

Z Offset on autoleveling sensor setup

How does Z offset (M851) work with an auto leveling sensor? Does it add the Z offset to the offset of the G29 mesh? or the ...
5
votes
1answer
2k views

Problem with print bed height on Creality Ender 4

I am a novice to 3D printing and have encountered an issue that I cannot seem to solve. Hopefully someone here can point me in the right direction. I have a Creality Ender 4 that I purchased a few ...
7
votes
1answer
1k views

Marlin's bed leveling Mesh Validation Pattern ignoring home offset

I'm using a Prusa clone with Ramps 1.4, Marlin 1.1.5 and an inductive proximity sensor Z-probe. Due to the design of the printer, the X and Y end-stops and the Z-probe are not exactly aligned with the ...
2
votes
1answer
995 views

Auto bed leveling with BL Touch sensor crashing to bed

I'm new to 3d printing and I recently bought a Geeetech Prusa i3 Pro B along with a BL Touch (3D touch) sensor to do auto bed leveling. I printed the sensor holder, mounted it and the sensor to the ...
2
votes
1answer
464 views

Tevo Tarantula incorrectly auto leveling of bed

I decided to try and setup the bed auto level sensor. I downloaded this firmware: TEVO-Tarantula-I3-Marlin-Firmware and followed this tutorial, YouTube - Setting Up Auto Bed Leveling (Tevo Tarantula)....
5
votes
2answers
4k views

Auto leveling with Marlin and RAMPS 1.4 does not work

I configured Marlin 1.1.3 for auto-leveling with a fix mounted sensor connected to the Z end-stop pin. I have the following settings in my config: ...
6
votes
2answers
7k views

Nozzle jumps off the bed when using Marlin Mesh Bed Leveling

I am using Marlin firmware with a RAMPS board on an Anet A8 printer. The bed size for the printer is 220 x 220 mm and that is stated in the configuration.h file. ...
4
votes
2answers
3k views

Assisted manual levelling with Marlin

Marlin offers a bunch of different choices for auto-levelling and assisted manual levelling for bent build plates (mesh levelling), but for the moment I want to level things completely manually. That ...
5
votes
1answer
397 views

Printrbot simple metal not auto leveling

I have a printrbot simple metal with the heated bed upgrade. Its been working fine until Cura updated, now, after the x,y, and z axis zeros, the print starts without moving to the other corners and ...

1 2
3