Questions tagged [bigtreetech]
For bigtreetech displays, drivers, modules, motherboards.
14
questions with no upvoted or accepted answers
4
votes
0
answers
952
views
How to get dual Z, dual Y steppers and dual endstops working on Marlin?
I've been trying for days to get my BTT SKR2 board to work with both dual Y & Z-axis and independent end stops (2 per axis). The Y-axis does independent homing just fine no matter which way the ...
3
votes
0
answers
952
views
Connecting 128x64 OLED to BIGTREETECH SKR mini E3
I'm trying to connect a 128x64 OLED display with the SH1106 driver for the BIGTREETECH SKR mini E3 printer controller board which uses the 32 bit STM32f103RC MCU.
Note that it works fine with my ...
3
votes
0
answers
6k
views
How do I install the USB drivers for Bigtreetech's SKR Mini E3 v1.2?
I want to install the USB drivers for the BIGTREETECH SKR Mini E3 v1.2 from the GitHub page but I don't know how to proceed.
Any help will be greatly appreciated.
1
vote
0
answers
123
views
What causes an unstable ethernet connectivity with Manta M8P/CB1?
I'm working with a Manta M8P and CB1 and the environment I'm working in requires it to be directly connected to the PC via an ethernet cable. (Wi-Fi or ethernet connection to the router is not ...
1
vote
0
answers
233
views
Bigtree GTR V1.0 + M5 (Klipper) Can Klipper access my M5 expansion board?
Just a quick question, Does Klipper support Expansion Boards?
1
vote
0
answers
22
views
Can't connect PowerBelt3D Zero to Print Server
I have tried connecting via Repertier, Pronterface, and OctoPrint. All of them fail to get a response from the handshake attempts. The OctoPrint "AUTO" setting will automatically try all ...
1
vote
0
answers
197
views
Extruder motor freezing
I recently upgraded from a Creality 4.2.7 controller board to a BigTreeTech SKR E3 Turbo and touch screen. When power is applied, the extruder motor turns slightly, then freezes and has a low humming ...
1
vote
0
answers
128
views
Steel heatbed - White stains after cleaning with IPA
So, I'm new at 3D printing and I've tried cleaning my new 3D printer's steel heated bed with Isopropyl Alcohol and it left some very nasty white marks all over the bed.
I tried cleaning it off with ...
1
vote
0
answers
202
views
TMC2208 v1.2 stepper motor drivers not detected on SKR 1.4 turbo with RepRap firmware
I've upgraded my board to SKR1.4 Turbo with RepRap firmware. Everything works, but motors move double the request. M112 reports them as 'no-driver-detected'.
...
1
vote
0
answers
682
views
Ender 3 Pro with BLtouch + BigTreeTech Auto level not compensating
As the title says, I have an Ender 3 Pro + BLtouch v3.1 and BigTreeTech SKR mini E3 v2.0. I have the SKR loaded with "firmware-bltouch-for-z-homing.bin" but my printer does not seem to be ...
1
vote
1
answer
1k
views
Getting BTT filament sensor to work
(This is a pretty much duplicate post from one I put over on the Reddit, but it hasn't received a lot of traction over there so I figured I'd post):
Like many posts I've seen on the internet, I'm ...
0
votes
1
answer
459
views
Mixing (closed loop) stepper drivers on MKS main board
Can I mix BIGTREETECH S42B closed loop stepper drivers on the MKS Gen L controller board with other drivers?
Are the pins in the same position? Would mixing work?
0
votes
0
answers
169
views
Ender 3 nozzle moves through previous layer on lithophane
I'm trying to print lithophanes and having an issue with the nozzle moving through the previous layer and basically "drawing" through the print.
I've printed 3 lithophanes before with zero ...
0
votes
0
answers
801
views
TFT35 and G-code preview
Is there a way to have the Bigtreetech TFT35 v3.0 show a G-code preview while printing - similar to the MKS TFT35?