Questions tagged [creality-cr-10]

For questions about the Creality CR-10 family of 3D printers

Filter by
Sorted by
Tagged with
11
votes
7answers
1k views

Noise Reduction

I am looking for methods to reduce the amount of noise produced by my CR-10. I have the printer in my downstairs study and if I'm doing a long print job, you can hear it upstairs in my son's bedroom ...
9
votes
3answers
3k views

Filament isn't going into the Bowden tube, instead it goes “into the room”

The pictures explain my problem. I have already tried to reduce the retraction but that showed no effect. Thank you for your help. The effect is a total stop of the print (no material is extruded). ...
7
votes
2answers
2k views

Nozzle heats up past the setpoint and increases

I made a few successful prints since I got my CR-10 two weeks ago and I didn't run into any major trouble. The printer is new. Today I set it to "preheat" mode while I was preparing the SD card with ...
6
votes
3answers
4k views

Filament extrusion always stops at some point during print

I own a Creality CR-10 (using Ultimaker Cura for slicing) and I am experiencing terrible printing problems. My problem: I am not able to print anything that takes several hours to print. For parts ...
6
votes
1answer
4k views

Question about retraction distance and stringing/print quality with PETG

I've tried printing the Basic Stringing Test on my CR-10S using PETG (250 °C nozzle, 80 °C bed) with different retraction distances leaving all the rest unchanged. In the image below you ...
5
votes
6answers
6k views

Creality CR-10S Pro 3D printer heated bed turns off after first few layers: normal?

When I run prints on my Creality CR-10S Pro 3D printer (using Ultimaker Cura as slicer), I set the heated bed to around 70 °C for PETG. after the first few layers, the heated bed set point ...
5
votes
2answers
19k views

Setup Creality CR-10 in Cura

Can anyone help me find/confirm the information needed to setup the CR-10 in the Cura Software I have following settings from research: Printer Settings x = 300 mm y = 300 mm z = 400&...
5
votes
3answers
5k views

Bed too close to nozzle?

I've been having some bed adhesion problems that I have been trying to solve by leveling the bed. I think that it's pretty level now but when I start a print the lines seem pretty flat. Is this true? ...
5
votes
2answers
2k views

Creality CR-10 Clogs and Underextrusion - Filament at fault?

I've been printing successfully on my CR-10 for the past year now. I've had issues now and then but have been able to look around the internet and solve them. I've been using some Flashforge white PLA ...
4
votes
3answers
479 views

Which capacitor to change on CR-10S S500 motherboard?

I have a CR-10S 500 and want to change a capacitor on it to improve and solve temperature issues. This capacitor that needs to be changed should be labeled as "C4" as mentioned on this post but it's ...
4
votes
3answers
903 views

Under-extrusion after a certain amount of successful layers?

My CR-10 is starting prints, BUT then makes weird spiral pattern, layers go up vertically with large gaps. Hollow infill. I don’t know if it’s: - My Slicing skills - original files - the printer ...
4
votes
1answer
825 views

Thermal runaway with specific prints

I have been experimenting with PETG on my CR-10 upgraded with an E3D all-metal hot end and Marlin firmware on the controller. I am printing with 0.8 mm nozzle at 250 °C and an 85 &...
4
votes
1answer
3k views

Low Filament Sensor for Creality CR-10? [closed]

I have been playing with my CR-10 for about a month now and I was wondering if there is a low filament sensor available for the CR10. I found this listing on Amazon, Creality 3D Printer CR-10 S4 ...
4
votes
1answer
1k views

CR-10S / Ender5+ LCD Touchscreen Firmware Editing

How would I go about editing the LCD menus for the touchscreen? Oddly the ender5+ is supposed to be an upgrade but the ender5 (regular) has so much more stuff you can control from the lcd screen. ...
3
votes
4answers
9k views

Clogging due to heat creep: buy new cooler or new hotend?

Sadly, I am not able to "repair" my 3D printer. Every time, I want to print something that takes a bit longer to print, the extrusion stops at some point during the print (the first few layers are ...
3
votes
2answers
483 views

How to measure the nozzle diameter?

On a Creality CR-10 Max, there is a bag of unidentified spares, which include three unmarked nozzles. There is a needle that is exactly 0.4 mm in diameter, which needle fits exactly inside one of ...
3
votes
3answers
1k views

Nozzle insulation gone, can the printer be damaged?

During a print a lot of plastic ended up ripping the nozzle's yellow insulation strap. Can printing without this insulation around the fusion chamber damage the printer? If there is no chance of ...
3
votes
2answers
3k views

What are the specifications of the dual voltage controller of the Ender 3/CR-10?

Following on from What level of voltage does the Creality Ender-3 run at? Dave's answer states that both 12 V and 24 V can be used on the controller board. It also goes on to say that the ...
3
votes
2answers
2k views

CR-10 randomly pauses for a few seconds

I thought I have already had and fixed every problem one could possibly have with a 3D printer. Guess I was wrong. I haven't used my Creality CR-10 for a few weeks, everything was working the last ...
3
votes
1answer
32 views

CR-10 heating problem

I've been happily printing on my CR-10 for a couple of months but now there is an issue. As soon as I turn it on the hot-end begins heating. I have replaced the heater and the thermistor but the ...
3
votes
1answer
433 views

CR-10S Pro pausing and starting again

I found this question, CR-10 randomly pauses for a few seconds, that someone asked earlier. I am experiencing the exact same thing, only on a CR-10S Pro. None of the suggestions on that post helped. ...
3
votes
1answer
2k views

Creality CR-10 extruder clicking and/or nozzle clogging

So I am fairly competent with 3D printing, but this problem has got me stumped. I use a Creality CR-10 and I hadn't printed anything off for quite a while (maybe 5 or 6 months?) and I just recently ...
3
votes
2answers
83 views

Possible causes of print defects?

I'd like some advice regarding defects on my print : Here some details : Printer CR-10 S, nozzle 0.4 Material PLA Bed 60, Hotend 215, 50 mm/s speed SLiced with cura 4.1, 5 walls (i can provide more ...
3
votes
2answers
635 views

Error when trying to upload firmware to cr-10

I've been having trouble uploading the TH3DUF_R2 firmware to my CR-10. I've already successfully flashed the bootloader using my Arduino, but when I try to upload the bootloader I get this error: <...
2
votes
2answers
1k views

Problems with bed leveling of Creality CR-10 Mini

So I've had my CR-10 Mini for some months now, and I've been continually having strange problems with bed leveling. Basically, after leveling the bed and printing a part, the bed is no longer leveled ...
2
votes
1answer
2k views

Stepper motor for CR10-S5 Y-axis

I need to replace this stepper motor with the following product identification: It’s a Y-axis for CR10-S5 and labeled as JD42HS60-1500A-02F. What type of stepper motor is this?
2
votes
2answers
165 views

Problems with under extrusion and clogs on CR-10

I've asked a question before on the extruder gear clicking on my CR-10, but I'm certain its because of the nozzle getting clogged for some reason. I'm using a standard 0.4 mm nozzle with white ...
2
votes
1answer
469 views

How sensitive are all-metal print heads?

So my goal was to print in a variety of materials with my CR10, but all attempts up to now have failed. I've tried a variety of all-metal hot-ends (except Micro Swiss) with no success. For those with ...
2
votes
1answer
177 views

What precautions to take when flashing Marlin 2.0?

I was just informed via a comment that the TH3D Unified firmware a version of Marlin that's no longer updated and considered obsolete (1.9.X in this case) and that, since I'm flashing my firmware to ...
2
votes
0answers
67 views

Scaling mechanism in Creality Slicer 1.2.3 for super small/large STL

I am having a tough time to understand scaling out and in STD files loaded into the Creality Slicer 1.2.3. For instance an STL like this: ...
2
votes
0answers
37 views

Over-extrusion on curved surfaces?

I am having issues with my Creality CR-10 S5 running Cura 4.6.1. If I use the Ender-3 gcode, it prints perfect. If I do the exact same print with S5 printer selected, I get garbage prints with lots of ...
2
votes
0answers
34 views

Printer starts normally then becomes insanely slow

After having replaced the Creality factory firmware by a recompiled one to manage a BLTouch sensor I have the following behavior on my CR-X (mainboard Creality V2.2, firmware Marlin 1.1.6 + additions ...
2
votes
1answer
746 views

BLTouch missing build plate on levelling

I have finally sorted the problems out with the frozen screen, but inevitably there's always more to take there place. I have installed the latest version of the 'Tiny Machines' Firmware but on ...
2
votes
0answers
380 views

CR10S Pro Pausing the print at a certain layer height

Im printing on a CR10S Pro and I can't find a way to pause the print at a certain height, to insert magnets into my print. Is there a way I can do this?
2
votes
0answers
271 views

BLTouch Deploying then immediately retracting while homing

I just bought a Creality CR10 Max (this is my 9th printer, 3 of my others are creality and they all have a BLTouch installed). I have only made probably 5 prints on this machine since I bought it ...
1
vote
2answers
103 views

When do I need to get a BLTouch upgrade?

I've found many Youtube videos of makers upgrading to BLTouch sensor. I have a Creality CR-10S Pro, so far bed leveling hasn't been an issue (after some days of trial and error). My question is ...
1
vote
1answer
259 views

Strange banding on first layer/skin

I've been printing for a while with a Creality CR-10S with Colorfabb black PETG economy and all was good. Until today, where on a large, flat print (30x10cm - a small drawer) I can't manage to get a ...
1
vote
2answers
3k views

Proper wire gauges for extending all CR-10S wires

I want to extend all my CR-10S wires. I have two long wire types: 22 and 18 AWG wires. I've done some research and found the following: Extruder heating element: 22 AWG or lower. Extruder thermistor ...
1
vote
1answer
2k views

Is endstop / z-probe wire required for BLTouch installation on CR-10S

I am confused about installing BLTouch on CR-10S. This is my motherboard: Below is a screenshot for the wiring of the BLTouch sensor: See the circled sections in yellow. Notice that the Z- socket ...
1
vote
1answer
55 views

Can't level CR10 as nozzle is touching the glass

I have a brand new Creality CR-10 S5. I'm new to printing. I'm trying to level the print bed, but after using the Auto-Home function the nozzle is left touching the glass. I understand that to do the ...
1
vote
1answer
31 views

How to feed the filament through the material shortage sensor?

I'm just finishing the set-up of a CR-10 Max. It is a new printer. I don't manage to feed the filament through the material shortage sensor. I can hear the micro switch click; the LED turns blue, then ...
1
vote
1answer
95 views

CR10 V2 under extruding and heating up too quickly

The heater cartridge on my CR10 V2 broke so I ordered a new one(12V). After replacing it the new one heats of very quickly past the target temperature and the slowly decreases to the target. Once it ...
1
vote
3answers
551 views

print pausing during printing

I got a new CR-10S 3D printer (I received it at Christmas). It has been printing just fine until yesterday, I was doing a print and it randomly paused, it did not restart on its own, I had to restart ...
1
vote
2answers
118 views

Odd dotting when printing a line

I tried printing a "improved" calibration cube and noticed that the printer was laying down dots instead of a solid line. This was right after switching out my extruder motor and tweaking retraction ...
1
vote
2answers
1k views

Extruder motor making a knocking sound, nozzle is not clogged

I've been trying to print anything for the past few days. Every time I go to print something the printer stops pushing plastic out and usually the motor makes a knocking sound. My original thought ...
1
vote
1answer
201 views

CR-10 Ignoring Z-Stop Switch, Keeps Trying to Lower

I have a CR-10 with TH3D's most recent firmware on it and an EZABL (Plug & Print Auto Bed Leveling Kit) installed. My problem is that when I select "Auto Home", the printer ignores the Z-stop ...
1
vote
1answer
262 views

Free UARTs TX and RX pins on CR-10S motherboard

I have a WiFi module that only needs two wires connection to work. These are RX and TX pins connected to Arduino or the CR-10S printer board but I don't know if there is any physical or software UARTs ...
1
vote
1answer
610 views

Creality CR-10 slightly jerks when moves from right to left

So when CR-10 prints square (like on the video starting from 6 second) while being in the top right corner extruder jerks i.e. slightly moves to the right and then continues movement to the left. So ...
1
vote
1answer
41 views

Creality CR-10 board upgrade from V1.0 to V2.0 questions

I have a base Creality CR-10 that I have had for 10 months. Since then I have added Z-axis braces and a Z-axis dual lead screw. I have a Filament runout sensor that I want to add and I want to add a ...
1
vote
1answer
64 views

Why is BLTouch Still Probing Off the Bed Even When `NOZZLE_TO_PROBE_OFFSET` is Set?

So I am almost finished upgrading my CR10s with Hemera and BLTouch hardware, however I can't get past this one problem. In the picture, you can see that the probe is to the left of the nozzle, and ...