Questions tagged [creality-ender-3]

For questions about the Creality Ender 3 family of 3D printers

Filter by
Sorted by
Tagged with
3
votes
1answer
25k views

How to set the boundaries for BLTouch probing

I have just installed the BLTouch on my Ender 3 running Marlin 1.1.9 and I want to set it up so the probing does the 9 points in a perimeter that uses most of the bed surface area. At the moment the ...
5
votes
1answer
569 views

Getting a Cura Raft to stick to the object more firmly (for ABS)

I have been have a problem printing ABS with Cura on an Ender 3. I am getting good bed adhesion on the raft, but the object on top of the raft easily curls off it. See photo below. Settings: Bed ...
4
votes
3answers
3k views

Ender 3 Z-limit now unreliable - possible causes and solutions?

I had a couple of recent nozzle/bed crashes, so I now frequently do a manual bed levelling. I do these while the bed is heated to allow for expansion. Today i found, after levelling, a subsequent ...
4
votes
1answer
2k views

Creality Ender-3 slanted nozzle

I’ve just received my first 3D printer, the Ender-3 and while assembling the unit I noticed that the nozzle is slanted and not vertical on its holder unit. Is this normal or do I have to try to make ...
6
votes
3answers
1k views

Adding additional extrusion to a raft (raft with a skirt?)

I started using rafts more often, to get better results with complex or fragile parts, but my Ender 3 consistently under-extrudes the initial outside line of the raft (for the first inch or two, where ...
2
votes
1answer
6k views

Ender 3 seemingly speeds up too much on straight long shell lines

After few good prints with my new Ender 3, I noticed that prints with longer shell straight lines (> 5 cm) have extrusion problems in the middle of those lines. I figured that this might be ...
5
votes
3answers
7k views

What parts are suitable replacements for an Ender 3 Pro?

I'm new to 3D printing and I recently got my first 3D printer, an Ender 3 Pro by Creality. I've tried to find information about the type of nozzles should I look for. I'm trying to find stainless ...
4
votes
0answers
62 views

How to print an item the size and thickness of a laptop display? [duplicate]

I want to print a case for a laptop display that I plan to turn into a second display. I have the Ender 3 printer, with a print area smaller than the case's size. ...
4
votes
3answers
2k views

What is the point of diminishing returns on the STL refinement level in Fusion 360 on an Ender 3?

When exporting an STL from Fusion 360, one must select an STL refinement level to use for calculating the maximum triangle count. For FDM printing (0.05mm and above layer heights), where is the ...
4
votes
1answer
5k views

Does the Ender 3 need an 8 pin mini USB or 5 pin, or no difference?

I've been searching for a reassuring answer for a week now. What type of mini USB does the Creality Ender 3 need? I have studied about them and five pin seems to be the answer but I haven't found a ...
5
votes
2answers
3k views

PETG filament doesn't stick reliably to fake Buildtak surface

I just got my first spool of PETG and tried to calibrate an Ultimaker Cura profile for it on my Ender 3 today with limited success. I've had severe issues with the filament not sticking to the build ...
4
votes
3answers
3k views

Ender 3 is capable of food safe printing?

I've been looking into the viability of manufacturing a replacement part for a kitchen blender that has a broken part. I found this page that talks about what makes a print food safe. One of the items ...
4
votes
2answers
14k views

Ender 3 Calibration Cube Fail + Can't Print Circles

After noticing that my ender 3 couldn't print a 'perfect' circle I decided to use a calibration cube to see if that could be the issue. These were my results: I did have some successful prints before ...
5
votes
2answers
4k views

Sudden underextrusion on Ender3

I have printed a couple weeks perfectly fine with my Ender 3. Two weeks ago I changed the firmware but the settings were all fine and resulted in good prints. Now, suddenly during a print the ...
6
votes
7answers
3k views

Electric shock from ender 3 printer PSU

I had recently purchased an ender 3 and after setting it up and plugging it in, I received an electrical shock from the power supply. I live in the UK and so I was provided an EU to UK adapter which I ...
5
votes
3answers
11k views

Strange layer separation issues on Ender 3

I got my Ender 3 a couple weeks ago. Within a couple days of test prints, I was able to get it working pretty well. Prints looked great. However, I installed a more permanent solution to my X-Gantry ...
10
votes
3answers
43k views

Ender 3 nozzle homes off the bed in the Y axis

I just received my new Creality Ender 3. I was going through and checking/adjusting everything for alignment, and I noticed that when you "auto home" the print head, the nozzle stops off the ...
3
votes
2answers
3k views

What are the specifications of the dual voltage controller of the Ender 3/CR-10?

Following on from What level of voltage does the Creality Ender-3 run at? Dave's answer states that both 12 V and 24 V can be used on the controller board. It also goes on to say that the ...
9
votes
3answers
72k views

Recalibrating Home-position

I got myself the Ender 3. The Home position is about 1 mm left and 2 mm in front of the front left corner. Now, the hotend center axis is 11 mm from the carrier plate with the "Mk 10" cooler ...
8
votes
3answers
6k views

Inductive Sensor in 24 V machine?

I am getting a 24 V based Ender 3. From the factory, it has an aluminium bed. So I also put this LJ12 A3-4-Z/BX Inductive NPN NO 4 mm with 6-36 V operation current into the box together with ...
6
votes
3answers
30k views

What voltage does the Creality Ender-3 run at?

I am pondering about buying a Creality Ender-3, and I am honestly confused about some reviews. Some claim it is running 24 V, one did claim it was 12 V, most don't mention it. Since I know about some ...

1 2 3 4 5
6