Questions tagged [creality-ender-5]

For questions about the Creality Ender 5 family of 3D printers

Filter by
Sorted by
Tagged with
0
votes
0answers
2 views

SKR E3 mini Ender 5 Enclosure cooling system

I was hoping I could find some help as I am not that familiar with marlin. I currently have an ender 5 and I am in the process of replacing the stock board. So here’s what I am trying to do: I have ...
0
votes
0answers
11 views

Ender 5 Plus not going “home” (or zero) correctly

I have been successfully using the Ender 5 Plus for a month now. But suddenly the printer wont go back to zero or "home" correctly. Whenever you press home or start a print it should go and ...
0
votes
0answers
11 views

Ender 5 Plus X and Z axis stopped working. Only Y will move using control panel

Everything was running fine, I was able to level the bed and run auto level, I was just getting ready to print. I was running filament that broke, so I unplugged the tube from the nozzle assembly to ...
0
votes
0answers
23 views

Nozzle prints higher than what it should after first layer

I am new to 3D printing. I am using an Ender 5 Pro with the SKR Mini v1.2 control board. The bed is leveled and the nozzle height is set correctly. The firmware is TH3D UFW 2.10. My first layer prints ...
0
votes
1answer
50 views

Ender 5 (Plus) - Gantry not square to frame, how to fix?

How would one go about squaring the gantry relative to the frame? Referring to the image below, distance A and distance B are not equal. Also would this account for the reason why when I attempt to ...
1
vote
1answer
73 views

Problem printing bigger models in the Ender 5

In all the bigger prints I print on my Ender 5 with PETG I have problems with warping and raft detachment during printing. I have a glass bed and I'm using Ultimaker Cura 4.6.1 standard printing ...
0
votes
0answers
195 views

Creality-Ender 5 Plus bed leveling out of bounds [closed]

I just received my first 3D printer. I am trying to level the bed for my first print. The X-axis won't move side to side but it shakes in its current position. The Y-axis won't move to the back half ...
0
votes
0answers
47 views

BTT SKR 1.4 Turbo SPI setup

Can anyone confirm that on the SKR 1.4 Turbo you don’t need any of the jumper wires to enable SPI mode? Like you would do on the 1.3 variant? As I have searched and cannot seem to find any reference ...
0
votes
0answers
108 views

Patchy first layer on glass bed

The part at the front has only one layer, and has what appears to be uneven patches. The part at the back has had two layers, so it clears itself up. The build plate is flat, and level (I levelled it ...
2
votes
1answer
615 views

Why the Ender 5 Pro can't remember the axis position or cant move back to home anymore?

I am completely new to 3D Printing. I got my first printer a Creality Ender 5 Pro yesterday. My problem I did shutdown the printer without the axis being in home position (X: 0, Y: 0, Z: 320 instead ...
0
votes
0answers
56 views

Ender 5 pro , prints lean, but only when multiple parts are printed (almost)

I can print single, large, complex parts with multiple towers with long travels between them and nothing leans. So pretty sure it is not belt tension, lash, or slop. When I add a second part to the ...
1
vote
0answers
45 views

PLA Warps despite every effort to prevent it

I am using a Creality Ender 5 with a tempered glass bed. I could say that I am a seasoned 3D printing hobbyist but I am really out of ideas in this case. Currently I am using a grey colored PLA that ...
0
votes
1answer
238 views

Do you need to manually level the bed with a BLTouch? Adhesion issues with Ender 5 and BLTouch 1.3

I've just installed a BLTouch on my Ender 5 Pro and updated the firmware to 2.0.5.3 and enabled BL touch. I can send a G29 which probes all the points correctly, I ...
0
votes
0answers
34 views

Inconsistent wall width

So I'm trying to calibrate my flow and I'm printing the walls of a 20x20x20 mm cube. I have a 0.4 mm nozzle and I'm printing 2 wall lines and ideally I should end up with a wall thickness of ...
0
votes
0answers
105 views

How to remove a stripped nozzle

A few months ago I got an Ender 5 printer. After a few successful prints with only PLA, I started getting a lot of issues. The last time I came back after an hour and there was just a bird's nest ...
3
votes
2answers
80 views

Nozzle jiggles when screwing into heating block

I've had the Ender 5 Pro, as is, for 3 months. After I tried a cheap PLA filament (maybe too cheap), it clogged the nozzle. I cleaned it, but any other filament I have would have similar problems ...
0
votes
2answers
79 views

Advice on power supply wiring for the UK

I've been looking at the Ender series and decided to take the plunge. But I'm unsure on electrical matters. The 110 or 220 volt switch, I assume goes to 220 V as I live in the UK but my main ...
1
vote
1answer
3k views

Gaps/Holes in the 3D Print walls

I'm new to 3D printing, I bought an Ender 5 Pro just recently. Trying to print with 1.75 mm PLA, but the results are very bad, unfortunately. When I got after bed leveling I got a decent result ...
1
vote
1answer
55 views

PLA support material suddenly a problem on Ender 5

I have an Ender 5 that I meticulously calibrated with good success and was regularly getting great print quality with PLA. I stopped using it for a couple of months and when I resumed (without having ...
2
votes
0answers
1k views

Ender 5 Pro print quality issue

I got my 3D printer from Creality 1 day ago. My dog off the SD card came perfectly, Benchy was also printed almost flawlessly. I used standard Benchy settings on all my prints. Now I tried making a ...
0
votes
0answers
1k views

Ender 5 Plus offset issue

Me: Experienced coder, Entry level 3D print person. Setup Ender 5 Plus Creality V2.2 Board BLTouch Marlin Titan Aero Notes: Using a custom mount for the head and probe. Front Left Top is 0,0,0 X/Y ...
0
votes
0answers
29 views

Ender 5 plus center of bed is incorrect [duplicate]

Currently have an issue setting the center of the bed. Have tried using offset in Cura, without any effect. Ender 5 Titan aero Creality v.2 Cura 4.4.1 This is causing issues as the print job goes ...
1
vote
3answers
456 views

Does an enclosure need a roof to print ABS?

I have an Ender 5 printer, which is a frame-based printer with no enclosure. However, I want to print ABS. Some experiments with a massive cardboard box have shown me I need an enclosure. Because the ...
1
vote
2answers
349 views

MKS GEN L unknown motherboard error

This is my first time asking for some help on here and I have Googled, but only found a few reference to this issue. I know I am doing something dumb but I have no clue what it is. I get an unknown ...
6
votes
1answer
1k views

Lines appearing during ironing

I'm new to 3D printing, but have been having relative success with the Ender 5 Pro and Cura. I'm making some coasters and using the ironing feature to smooth out the top layer. This is mostly working ...
2
votes
0answers
552 views

Ender 5 Printing Issues

I'm brand new to 3D printing. Just got me an Ender 5 Pro. After messing around for the last couple of days with bed leveling, I'm finally able to get consistent first level all thought I have to ...
4
votes
1answer
1k views

CR-10S / Ender5+ LCD Touchscreen Firmware Editing

How would I go about editing the LCD menus for the touchscreen? Oddly the ender5+ is supposed to be an upgrade but the ender5 (regular) has so much more stuff you can control from the lcd screen. ...
0
votes
1answer
57 views

Problem with first and last layers

I bought Ender-5 and if I print sample model in bundle SD, it’s just perfect. But when I tested basic cube with raft, its base and top is just ugly. Even thought its 4 sides are perfect. Ultimaker ...
4
votes
1answer
3k views

Ender 5: Bowden tube shifts in/out of extruder during retractions

I have an Ender 5 with an aluminum extruder that was printing beautifully for a few days after building it. I received a Capricorn bowden tube and new couplings as a gift, and replaced those, and now ...
14
votes
5answers
9k views

Why keep the bed heated after initial layer(s) with PLA (or PETG)?

I'm printing on an Ender 5 with the default flex/magnetic build surface. I read that PLA and PETG may sometimes be printed without any bed heating at all and also that bed heating is the main ...
2
votes
2answers
2k views

How would you clean/prepare a flexible/magnetic mat (e.g. Ender 5) as compared to a glass bed?

I have started printing about a month ago on an Ender 5 (using mostly PLA but recently also PETG) and it seems it's about time to give the print bed a more thorough cleaning than what I usually do ...
1
vote
2answers
517 views

Ender 5 Slant or Leaning when printing multiple parts

Getting slanted or leaning prints when printing multiple parts. I checked the eccentric nuts and belts aren't rubbing anything. All works well when printing a single part. But multiple parts: What am ...