Questions tagged [creality-ender-5]

For questions about the Creality Ender 5 family of 3D printers

Filter by
Sorted by
Tagged with
3
votes
3answers
6k views

Why the Ender 5 Pro can't remember the axis position or cant move back to home anymore?

I am completely new to 3D Printing. I got my first printer a Creality Ender 5 Pro yesterday. My problem I did shutdown the printer without the axis being in home position (X: 0, Y: 0, Z: 320 instead ...
0
votes
0answers
156 views

Ender 5 pro , prints lean, but only when multiple parts are printed (almost)

I can print single, large, complex parts with multiple towers with long travels between them and nothing leans. So pretty sure it is not belt tension, lash, or slop. When I add a second part to the ...
1
vote
0answers
53 views

PLA Warps despite every effort to prevent it

I am using a Creality Ender 5 with a tempered glass bed. I could say that I am a seasoned 3D printing hobbyist but I am really out of ideas in this case. Currently I am using a grey colored PLA that ...
0
votes
1answer
5k views

Do you need to manually level the bed with a BLTouch? Adhesion issues with Ender 5 and BLTouch 1.3

I've just installed a BLTouch on my Ender 5 Pro and updated the firmware to 2.0.5.3 and enabled BL touch. I can send a G29 which probes all the points correctly, I ...
0
votes
0answers
331 views

How to remove a stripped nozzle

A few months ago I got an Ender 5 printer. After a few successful prints with only PLA, I started getting a lot of issues. The last time I came back after an hour and there was just a bird's nest ...
3
votes
2answers
183 views

Nozzle jiggles when screwing into heating block

I've had the Ender 5 Pro, as is, for 3 months. After I tried a cheap PLA filament (maybe too cheap), it clogged the nozzle. I cleaned it, but any other filament I have would have similar problems ...
0
votes
2answers
366 views

Advice on power supply wiring for the UK

I've been looking at the Ender series and decided to take the plunge. But I'm unsure on electrical matters. The 110 or 220 volt switch, I assume goes to 220 V as I live in the UK but my main ...
1
vote
1answer
15k views

Gaps/Holes in the 3D Print walls

I'm new to 3D printing, I bought an Ender 5 Pro just recently. Trying to print with 1.75 mm PLA, but the results are very bad, unfortunately. When I got after bed leveling I got a decent result ...
1
vote
1answer
97 views

PLA support material suddenly a problem on Ender 5

I have an Ender 5 that I meticulously calibrated with good success and was regularly getting great print quality with PLA. I stopped using it for a couple of months and when I resumed (without having ...
3
votes
1answer
5k views

Ender 5 Pro print quality issue

I got my 3D printer from Creality 1 day ago. My dog off the SD card came perfectly, Benchy was also printed almost flawlessly. I used standard Benchy settings on all my prints. Now I tried making a ...
0
votes
0answers
3k views

Ender 5 Plus offset issue

Me: Experienced coder, Entry level 3D print person. Setup Ender 5 Plus Creality V2.2 Board BLTouch Marlin Titan Aero Notes: Using a custom mount for the head and probe. Front Left Top is 0,0,0 X/Y ...
1
vote
3answers
1k views

Does an enclosure need a roof to print ABS?

I have an Ender 5 printer, which is a frame-based printer with no enclosure. However, I want to print ABS. Some experiments with a massive cardboard box have shown me I need an enclosure. Because the ...
1
vote
2answers
813 views

MKS GEN L unknown motherboard error

This is my first time asking for some help on here and I have Googled, but only found a few reference to this issue. I know I am doing something dumb but I have no clue what it is. I get an unknown ...
7
votes
1answer
3k views

Lines appearing during ironing

I'm new to 3D printing, but have been having relative success with the Ender 5 Pro and Cura. I'm making some coasters and using the ironing feature to smooth out the top layer. This is mostly working ...
2
votes
1answer
1k views

Ender 5 Printing Issues

I'm brand new to 3D printing. Just got me an Ender 5 Pro. After messing around for the last couple of days with bed leveling, I'm finally able to get consistent first level all thought I have to ...
4
votes
1answer
4k views

CR-10S / Ender5+ LCD Touchscreen Firmware Editing

How would I go about editing the LCD menus for the touchscreen? Oddly the Ender 5+ is supposed to be an upgrade but the Ender 5 (regular) has so much more stuff you can control from the LCD screen. ...
0
votes
1answer
70 views

Problem with first and last layers

I bought Ender-5 and if I print sample model in bundle SD, it’s just perfect. But when I tested basic cube with raft, its base and top is just ugly. Even thought its 4 sides are perfect. Ultimaker ...
4
votes
1answer
5k views

Ender 5: Bowden tube shifts in/out of extruder during retractions

I have an Ender 5 with an aluminum extruder that was printing beautifully for a few days after building it. I received a Capricorn bowden tube and new couplings as a gift, and replaced those, and now ...
14
votes
5answers
19k views

Why keep the bed heated after initial layer(s) with PLA (or PETG)?

I'm printing on an Ender 5 with the default flex/magnetic build surface. I read that PLA and PETG may sometimes be printed without any bed heating at all and also that bed heating is the main ...
2
votes
2answers
3k views

How would you clean/prepare a flexible/magnetic mat (e.g. Ender 5) as compared to a glass bed?

I have started printing about a month ago on an Ender 5 (using mostly PLA but recently also PETG) and it seems it's about time to give the print bed a more thorough cleaning than what I usually do ...
0
votes
2answers
1k views

Ender 5 Slant or Leaning when printing multiple parts

Getting slanted or leaning prints when printing multiple parts. I checked the eccentric nuts and belts aren't rubbing anything. All works well when printing a single part. But multiple parts: What am ...

1
2