Questions tagged [creality]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
1
vote
0answers
14 views

Creality 1.2.3 does not recognize M140 and 104?

For some reason, the Creality Slicer 1.2.3 ignores the M140 and M104 commands completely, even if I put them at the very ...
1
vote
2answers
77 views

Creality 10S 3D fan speed settings and bed temperature

What fan speed should I use with PLA? Do I need to manually set the fan speed in ‘Control’? Also, on the filament cartridge Bed Temp is listed: "No heat/60-80 °C". Does this mean heating the ...
1
vote
2answers
66 views

Resin layer for adhesion: how should I do it?

Backstory: Like quite a lot of people here, I'm having problems with parts adhering to the build plate of a resin printer. I've tried everything that I can think of: cleaning & re-sanding the ...
2
votes
1answer
111 views

HALOT BOX makes objects with support move up

I'm trying to slice some models using the default HALOT BOX software from Creality, which comes with the Halot One resin 3D printer. I've oriented them at 45 degrees, and am using supports. When I ...
1
vote
1answer
73 views

How to restore languages to Creality CR-6 SE after firmware update?

I have been battling print issues since my purchase of a new Creality CR-6 SE. I chose to do a firmware upgrade to see if it's perhaps a patched issue. I used the Creality Download page and downloaded ...
1
vote
0answers
32 views

Creality CR 6 SE firmware

I recently bought Creality CR 6 SE, I learned there are third party firmware available, I want to know which one is best known for CR-6
-2
votes
2answers
913 views

Creality Ender 6 Heating failed error [closed]

I got this message from my Creality Ender 6 printer. Now every time I want to print, or when it heats up, the printer gives me this message. Can anyone please help with this?
0
votes
0answers
58 views

Ender 3 V2 bed slanted

I'm at a loss I have no idea what to do, I've tried everything I can think of. I've fixed my x-axis gantry, added silicon bed mounts, used washers, straightened out my BLTouch but still this is the ...
3
votes
2answers
6k views

Ender 3 Pro will not auto home correctly after mainboard & BLTouch upgrades

I made two updates to my Ender 3 Pro: Silent Mainboard and BLTouch. My printer head is way out of sync now. After I Auto Home, it moves along the X-axis to the left, hits the stop switch & moves ...
1
vote
2answers
514 views

How to wire 5 V proximity sensor Ender 3 V2?

I’ve got this proximity sensor which is a 5 V, it doesn’t say it can be used over 5 V. Can I use a buck converter or is it possible to wire it up direct to a 5 V source on the Ender 3 V2? What I don’t ...
0
votes
0answers
18 views

BLTouch goes behind print bed

I want to install Marlin 2.0 on my CR20 Pro but when I try to level the bed it goes behind the bed (in my direction on the Y axis). Here is my bed config: ...
2
votes
1answer
61 views

Is it possible to run 2 Ender 3's off one power supply?

I have 2 Ender 3's and I am limited to wall sockets to power both the printers at the same time. So I was wondering if it was possible to wire both the printers to a single PSU? As the printer uses a ...
1
vote
0answers
37 views

Problem with jitters with Ender 3

Recently I realized that I have been getting jitter-like rough surfaces on round parts of my models from my Ender 3. The jitters happen on the sides of the model, so the jitters would be happening in ...
2
votes
1answer
86 views

Mid-print issue, extruder issue?

I have succumbed to asking the community for assistance. I've been scratching my head and lost many late nights and time trying to figure out what is going on with my 3D printer. Please see the image ...
0
votes
1answer
84 views

What kind of thermal paste do I need for a heatbed thermistor?

I've got a new heatbed. The current heatbed has a screw in the middle of the bed with some kind of thermal paste (feels like silicone). Somebody on reddit said that it is very unlikely silicone, ...
0
votes
0answers
109 views

Not moving on X and Y axis

TL;DR I moved the printer head slightly without turning off the system and now only the Z-axis stepper motors work. I recently purchased an Ender 5 Plus. I managed to get three prints done and then ...
3
votes
1answer
3k views

Is Creality Ender 3 V2 Supposed To Come With Board V 4.2.2?

I recently purchased a Creality Ender 3 V2 ~1 month ago, and just yesterday installed a BLTouch. When looking at the motherboard, I noticed my board version is 4.2.2. Isn't the Ender 3 V2 supposed to ...
1
vote
2answers
829 views

CR6-SE fails to heat hotend to set point

TL;DR - Please help me rebuild my CR-6 SE so that I can move on Here's a link to the latest issue that I had to make proof of in a video: CR6-SE failed Basically, it's failing to reach/maintain ...
3
votes
0answers
256 views

Difference between Creality V2.1/V2.2 boards? Where to find datasheets?

I can't find an official datasheet for either board. Does anyone know where to find this information? Something that has max voltages, pinouts, etc. Also, what's the difference between the V2.1 and ...