Questions tagged [ender3]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
1 vote
0 answers
42 views

How to print more accurately 3D cube test?

I have print problems with my Creality Ender 3 S1 and I have calibrated all axes: Belts both X and Y axex Extremes of the X-axis horizontal structure have the same distance to the bottom of the ...
John Miller's user avatar
1 vote
2 answers
214 views

Ender 3v2 nozzle plunging into bed after finishing mesh (only changed springs)

Yesterday I was printing just fine. Today I put the new springs that I bought from Amazon. Swapped them out, went to level things and my Z-offset was of course way off. I have the ...
Joleme's user avatar
  • 11
-1 votes
1 answer
627 views

Ender 3 printer won't auto home [closed]

After building my Ender 3 printer, installing the CR touch auto bed leveling kit, and the Ender-3 Marlin2.0.6 CR-Touch or BLTouch firmware for it. I turned it on and tried to auto home but it just ...
3dNovice's user avatar
1 vote
1 answer
524 views

Ender 3 S1 Pro error "extrude below min temp" [closed]

When I start my print it goes to home the z-axis and then I get the error "extrude below min temp" error (I have an Ender 3 S1 Pro)
Mr. Magic's user avatar
0 votes
1 answer
116 views

Ender 3 v2 with CR Touch/BLTouch moving down but not up

My Ender 3 v2 with a CR Touch/BLTouch installed is only moving down, but not up! The display shows P Endstop when I try to move below around halfway up the gantry. ...
zurgeg's user avatar
  • 123
0 votes
1 answer
16 views

The nozzle becomes clogged in the smoothing mode

My nozzle gets clogged when it starts to do smoothing. Settings below:
Мульти студия's user avatar
1 vote
0 answers
19 views

How would I fix an under extrusion problem?

Hey all I have an Ender 3 V1 and I have a problem with it under extruding. Its not putting out enough PLA to stick and it just becomes a mess. (Bed has a magnetic PEI plate that only has a few uses) ...
Nick Vitale's user avatar
1 vote
0 answers
139 views

How to fix Y axis is off by 30 mm?

I have Ender 3 with Klipper. In my config: ...
Alex Buznik's user avatar
0 votes
0 answers
112 views

Ender 3 S1 Pro extruding/jamming on random layers

My relatively new Ender 3 S1 Pro with default extruder started to under extrude and jam on some layers. When it happens I can hear extruder skipping/clicking noises. I printed same g-code multiple ...
kzulis's user avatar
  • 1
0 votes
3 answers
6k views

How to fix "SD Init Fail" on Ender 3

My Ender 3 is showing SD Init Fail when the sd card is inserted. I tried rebooting, reformating the card etc. At first, I thought the card is damaged, so I bought a ...
Johnykutty's user avatar
4 votes
1 answer
151 views

Ender 3 Pro: X-axis moves too much during printing

I got an Ender 3 Pro yesterday and have been having a problem with all of my prints. Whenever the extrusion stops and the X-axis moves, it moves too far. For example, I tried printing a Benchy with 2 ...
DerFern's user avatar
  • 141
0 votes
0 answers
2k views

Ender 3 CR Touch Bed Levelling X axis offset

I upgraded my Ender 3 with the CR Touch, and updated the firmware (contacted Creality directly to get the correct version). I got Marlin 2.0.6. However when I try the bed levelling feature the first ...
Fusco Bhonsle's user avatar
1 vote
1 answer
103 views

G28 X does not home the hotend

I have a classic Ender 3 running Marlin-2.1.1 on a BTT SKR v1.3 board with TMC 2130 drivers. Wifi is connected with ESP3D on an ESP32-CAM board connected to a TFT port. The X endstop is on the left ...
Hansa G's user avatar
  • 31
1 vote
0 answers
54 views

Is it normal that my heated bed has up to 25 °C difference from center to edge?

I have an Ender 3 V2 pro with the Quinly bed adhered to the aluminium bed. I have a hard time getting my prints to stick well. (PLA as well as PETG). We finally found out that only increasing the bed ...
Hacky's user avatar
  • 679