Questions tagged [filament-jam]
The filament-jam tag has no usage guidance.
12
questions
0
votes
0
answers
15
views
Ender 3 v2 Print not consistent
I just got my first 3D printer (Ender 3 V2) 3 days ago and at first it was printing fine but yesterday it started painting dotted lines. I heard it could be a clog so I changed the Nozzle after trying ...
0
votes
0
answers
15
views
Anet A6: known hotend problems?
I've got an Anet A6, modified with bed-leveling sensor etc., which has given me good service for several years. I'm not in a position to spend lots of money on anything fancier, since at present at ...
7
votes
2
answers
793
views
How do I remove filament from the hotend of a direct-drive printer?
I have PrintrBot Simple Metal and over the course of today's use, I managed to get a piece of filament stuck in the hotend, just below the extruder gear. There's not really much to grab at, and my ...
2
votes
0
answers
234
views
Ender 3 Pro extruder keeps clogging
I'm fairly new to 3D printing and looking for help. I have an Ender 3 Pro and it's been working great up until about a week ago. When I preheat the extruder, the nozzle gets hot as it should, but it ...
5
votes
2
answers
1k
views
Clogging from heat creep, but only in the nozzle itself?
I have an all-metal V6 hotend clone that has worked in the past, but recently will clog very easily.
I've tried the following to address it:
Clean/replace the nozzle (0.4 or 0.5 mm, nozzle is hot-...
2
votes
1
answer
101
views
Prusa i3MK3S+ layer skip with polycarbonate (overheating?)
On the last couple of polycarbonate prints with my Prusa, one or more layers have been completely skipped (i.e. no material extruded). The rest of the print is fine save some minor warping. I'm ...
1
vote
1
answer
114
views
Filament Spool Stalls Extruder Motor Destroying Print
I am having the frustrating problem where my extruder motor starts skipping steps and stops extruding simply because my filament is wound too tightly. There are some parts of my filament that are so ...
3
votes
3
answers
2k
views
Filament Jamming in Hotend. Why?
This has me stumped. I had been printing normally until this happened. Below is an expurgated version of my headache over two days. Some help would be appreciated.
Printer is Hypercube Evolution (...
1
vote
0
answers
337
views
E3D V6 hotend gets jammed very frequently
In the past couple of weeks, my V6 hotend gets jammed very frequently. The nozzle is 0.4 mm and the printer is a D-Bot.
Here are some of the things I have tried so far,
Switched between the original ...
2
votes
2
answers
1k
views
PLA Jamming- is the heat break too hot or too cold?
I’m getting nothing but jams with a new BCN3D Sigma R19 printer, printing PLA at 195 °C, two brands (BCN’s own brand and Monoprice orange). 6.5 mm retraction, as used in BCN’s PLA profile. Using their ...
2
votes
1
answer
941
views
Filament getting stuck/nozzle is clogged
For some reason on my Raise 3D N2 plus with a Bondtech-Extruder I am sometimes seeing filament jams and sometimes it prints without any issues. I am using PLA at 215 °C.
When the filament is jammed I ...
1
vote
3
answers
670
views
Filament jam on the tube entrance
I have a problem in regards to filament jam, however I don't think that my case is any related to the extruder nozzle.
After 30 to 40 minutes printing my filament bends and get stuck on the tube ...