Questions tagged [firmware]

In electronic systems and computing, firmware is a type of software that provides control, monitoring and data manipulation of engineered products and systems. Use this tag for questions about the firmware of your 3D printer. Include name and version as well as custom modifications that might be helpful to understand your problem

21 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
4
votes
0answers
382 views

Connecting 128x64 OLED to BIGTREETECH SKR mini E3

I'm trying to connect a 128x64 OLED display with the SH1106 driver for the BIGTREETECH SKR mini E3 printer controller board which uses the 32 bit STM32f103RC MCU. Note that it works fine with my ...
2
votes
0answers
31 views

Bricked Mks Rumba+ Board after Power Supply Trouble

this is my first time posting on this forum, so bear with me: This is my first attempt at a RepRap project, and my go-to board has been the RepRapDiscount MKS Rumba+, since I wanted to have ...
2
votes
0answers
102 views

How to compile Marlin for Melzi board without bootloader?

I'm trying to enable a lot of features on my custom build of Marlin, and I'm having trouble fitting into a reasonable space limit. I'm compiling through the standard Arduino IDE with Sanguino board ...
2
votes
0answers
560 views

Inconsistent Auto Bed Leveling - Having To Calculate Z Offset For EVERY Print

I am having a problem with my Flying Bear P902 3D printer where I have to calculate the Z offset for every single print. I calculate it using this method (and store it in EEPROM) : Link to ...
1
vote
1answer
39 views

How is the extrusion rate matched to the movement speed?

A typical line of (depositing) G-code seems to set a maximum speed (F), a new position to move to (X,Y,Z) and a new extrusion distance (giving an filament distance for the move). The F is common for ...
1
vote
0answers
48 views

Marlin Firmware - Autostart only runs `auto1.g` but not `auto0.g`

Marlin has a feature that can execute a G-code file from an SD card when printer is turned on; this is called Autostart. Autostart is available on printers with an ...
1
vote
0answers
57 views

Roll back from Marlin 2.0 to manufacturer closed-source firmware

Because I needed to insert nuts in my prints and therefore G-code instructions in their file, I upgraded my printer firmware to Marlin as in here : At the beginning I ...
1
vote
1answer
495 views

BLTouch error Marlin 2.x (on SKR 1.3)

I have some issue with my BLTouch (I'm new to bed levelling) : I compiled Marlin 2.x (for my SKR 1.3) for a Antclabs BLTouch, and everytime I power on the printer, it shows this error message: ...
1
vote
0answers
125 views

E-steps somehow reset, how could it have happened

Background After installing a direct drive extruder (E3D Hemera) to my CR-10S, I calibrated the E-steps so that adequate extrusion would happen; going from ~95 steps/mm to ~390 steps/mm. ...
1
vote
0answers
327 views

Makerbot Replicator 2 LCD screen not turning on

I recently got a MakerBot Replicator 2 from somebody. When I got it, it was not in a working state. The problem is that the LCD screen does not turn on. When turning the printer on, the 5 V and ...
1
vote
0answers
57 views

Firmware upload

I have a 3d printer without a firmware. It's a Wanhao Duplicator I3. I try to upload a version, but I have a little problem, at uploading on melzi board, it's a V03 version. I try this tutorial : ...
1
vote
1answer
41 views

RF100 Settings after reinstalling firmware

I have an RF100 v.1 printer with stock software (again) onboard. After my attempt of changing firmware, the X-axis motor decided to stray printhead away out of the borders of the printer and somehow ...
0
votes
1answer
16 views

Ender 5 SKR Mini E3 — After Heating the Hot End Assembly Runs into the side of the printer

So I got the SKR mini E3 for my Ender 5 after hearing all the positive reviews. When it arrives I plug everything in, make sure it's secure and test the axis... they all worked correctly. I then ...
0
votes
0answers
27 views

SKR E3 mini Ender 5 Enclosure cooling system

I was hoping I could find some help as I am not that familiar with Marlin. I currently have an Ender 5 and I am in the process of replacing the stock board. So here’s what I am trying to do: I have ...
0
votes
1answer
36 views

“Err: MAXTEMP: E1” when THERMAL_PROTECTION_HOTENDS is disabled

I am trying to port Marlin to my Qidi Tech 1 printer which previously ran Sailfish 7.8. Everything worked fine on the old board, including the temperature sensors. All cables except for power, LCD, ...
0
votes
0answers
9 views

Ultimaker 2 Extended+ temp input change

My Ultimaker 2 Extended+ motherboard has 3 temperature sensor inputs: Temp 1, Temp 2, Temp 3. The Temp 3 is for the bed and the Temp 1 and 2 are for 2 potential extruders. Now my printer has only one ...
0
votes
0answers
41 views

BLTouch on Ender 3 pro going higher at each levelling point

A print I was doing failed half way through and was stopped. On the next print I set levelling to occur for the BLTouch but instead of doing this it went higher on each of the x,y coordinates. ...
0
votes
0answers
48 views

Translating values from marlin firmware to reprap firmware for Prusa i3 MK3S

I am also a beginner trying to understand the firmware values and getting to know my printer before I actually get the duet so please bear with me, do let me know when I have gotten the values or ...
0
votes
0answers
73 views

Can't upload Marlin firmware to 3D printer because of “error: reinterpret_cast from integer to pointer”

When trying to upload Marlin firmware to my printer I get this error: error: reinterpret_cast from integer to pointer I'm using Tevo Tarantula with board MKS Gen ...
0
votes
0answers
24 views

Trying to remove autolevel from G-code - offset from bed not correct

I’ve been having all kinds of trouble with really every part of the print procedure on my Lulzbot Mini 2 that comes before the actual extrusion starts. I think I can get around 90 % of my issues ...
0
votes
0answers
319 views

SKR 1.3 Thermistor input died

I've got an SKR 1.3 and the thermistor input for extruder 2 has gone bad. In firmware, I've attempted to change the TEMP_1_PIN to another in ...