Questions tagged [flashforge-adventurer-3]

Questions using this tag should involve the Adventurer 3 3D printer that is manufactured by FlashForge Corporation

Filter by
Sorted by
Tagged with
0
votes
0answers
48 views

Flashforge Adventurer 3 PETG under extrusion after Rapid Move

I have recently started 3D printing and have had fine success with both PLA and ABS. Now I am trying to make some parts for which I believe PETG to be the correct material. However, I have run into ...
0
votes
1answer
65 views

Unable to load new filament FlashForge Adventurer 3

I have a FlashForge Adventurer 3. I have just finished my sample filament today and tried to replace it with a new spool of filament. This new filament is by Hatchbox, instead of FlashForge. Besides ...
3
votes
1answer
360 views

What to do if filament spool won't fit in 3D printer

My sample filament has just ran out. Luckilly, I've already bought more filament. The only problem I have is that the spool for the new filament won't fit inside my 3D printer. The filament itself ...
1
vote
0answers
26 views

Printing issues of ABS on a Flashforge Adventure 3 nozzle blocked

I tried to print in ABS for my first time. I have had my printer for almost 2 years but have only just started to use it and have a total of 28 hours of print time. The job I tried to print was meant ...
2
votes
5answers
188 views

What are some good safety tips for a 3D printing beginner?

I have just bought my own 3D printer. However, I am now reading that there may be some safety risks to 3D printing. I will be taking some precautions, such as buying an enclosed 3D printer (the ...
0
votes
0answers
116 views

Flashforge Adventurer 3 - bed temperature not going over 89 °C

I have an issue with my Flashforge Adventurer 3. When printing with ABS, the bed temperature is not going over 89 °C. Additionally, when I connect to the printer with Flashprint, it displays a ...
0
votes
0answers
392 views

Has anybody successfully used Prusa Slicer with the FlashForge Adventurer 3?

I am trying to get rid of the FlashPrint slicer that comes with the Adventurer 3 due to its limited capabilities - to no success. Cura works to some extent, Simplify3D lacks some bottom layer patterns ...
0
votes
1answer
171 views

Running costs of 3D printing

In the year that I have had my Flashforge Adventurer 3 I have just had a second extruder head break. The replacement cost (in AUD) is 135.00. But, I'll also need a new nozzle and a replacement ...
2
votes
1answer
78 views

Flashforge Adventurer 3 Spool mounting

I have just purchased the above 3D printer and the mount for the spool does not fit the new spool. The external spigots are too large and there is no axle shaft that would have helped. This is a photo ...
0
votes
0answers
33 views

Flashforge Adventure 3 printer

Recently bought the printer for my son, right from the start it didn’t print well. We made some adjustments and got it working somewhat but now it keeps printing (Benchy) only half way up and starts ...
2
votes
5answers
6k views

Printing temperatures for ABS on a Flashforge Adventurer 3

I've recently acquired a Flashforge Adventurer 3 and am having difficulty printing with ABS. The initial layers seem to lay and stay pretty well, though after a few more moments, one side will peel up ...
4
votes
8answers
12k views

Flashforge Adventurer 3 Filament feeder loud thumping noise, not enough filament extruded

My Flashforge Adventurer 3 is not printing properly. Filament feeder makes repetitive loud thumping noise and not enough filament is extruded. Resulting print (if completed) is not solid. Results ...
5
votes
2answers
4k views

Extruder/nozzle keeps clogging up

I have an Adventurer 3 printer from Flashforge and every time I unclog it, it gets clogged up again. I’ve done about 6 or 7 prints with it. So after I unclog it, I load the filament and it comes out ...