Questions tagged [heated-bed]

Use this tag for questions about the Heated Build Platform or Plate (HBP) for 3D printers.

14 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
1
vote
0answers
114 views

TPU Plastic leaving residue in my bed

How do I remove the residue left by TPU plastic ? I used to print with ABS plastic and while it left a little bit of residue, I could remove it with Isopropyl alcohol and then scrap it with my spatula....
1
vote
0answers
43 views

Activating heated bed through a switch, or D-pin and TIP31 transistor

Recently the connection between the heated bed and my board blew out. I was able to solder a new connector onto the board and it worked for a day, but now it seems the SMT pad has come off the board ...
0
votes
1answer
28 views

Figure out max bed temperature

I have a Tronxy X8 (yes, I know, poor choice but I didn't know better) and after some years printing PLA, PETG and TPU, I am considering trying ABS, since I got myself a second hotend which can go up ...
0
votes
0answers
27 views

Heating problems on Anet A8

I've set the bed temperature to 60 °C, but it goes to 39 °C and stops heating up. I've set the hotend temperature to 190 °C, but it goes to 300 °C. Then DEF both of them
0
votes
1answer
25 views

Which material should I use to print a mounting adapter for the y-carriage?

I have purchased a replacement bed for my 3D printer. I wish to have it mounted on a single linear rail. Currently I am unable to drill properly into aluminum (due to problems with my drill). ...
0
votes
0answers
23 views

Damaged MKS Gen_L V1.0

My MKS Gen_L V1.0 is obviously damaged. Nothing is fried on The board. I didn't see the magic smoke coming out of it. It works but I can't flash the board anymore because I get the "avrdude ...
0
votes
0answers
96 views

How to attach PEI sheet to glass for high temperature printing?

I am using an Intamsys FunMat HT, which has a "ceramic glass" bed. I'm not sure what "ceramic glass" means, the stuff behaves like borosilicate in the way it either chips or ...
0
votes
0answers
22 views

Bed temperature is changing randomly

While printing the bed temperature is changing like this. If the print time is below 30 minutes, printers stops after print two layers. But longer then 30 minutes, finishing job. I changed bed ...
0
votes
0answers
31 views

Anycubic Mega S 3D printer: Filament is not exiting the nozzle correctly when printing

I have this weird problem with my brand new Anycubic Mega S. First of all I use the default "Normal 0.2" setting in Ultimaker Cura 4.8 and I am trying to print this *MICRO* All In One 3D ...
0
votes
0answers
24 views

CR-10 S Pro bed heating problems

I've had my bed continually heat up and not stop. I have replaced the SSR and replaced it with an identical-looking one and also replaced it with a MOSFET.
0
votes
0answers
110 views

Flashforge Adventurer 3 - bed temperature not going over 89 °C

I have an issue with my Flashforge Adventurer 3. When printing with ABS, the bed temperature is not going over 89 °C. Additionally, when I connect to the printer with Flashprint, it displays a ...
0
votes
0answers
39 views

Heated bed is not heating up

Hello I am building a clone of Prusa MK2. So I connected all the connections to the RAMPS 1.4 shield. I used Pronterface successfully to set the temperature of bed, but it did not heat up... So I ...
0
votes
2answers
329 views

How can I extend silicon hotbed wires safely?

I'm in the middle of building a D-Bot printer, and have run into a bit of an issue when it comes to the heat bed wires. The heated bed is an aluminum plate with a silicon heater attached to it, and ...
0
votes
0answers
157 views

RAMPS 1.4 LED 2 blinking when trying to heat up bed

On my i3 clone I've been trying to add the Anycubic i3 Ultrabase to my RAMPS 1.4 board and after adding the necessary configurations in the Marlin firmware I can heat up the bed. The issue is that it ...