Questions tagged [klipper]
For questions about Klipper Firmware
14
questions
2
votes
0
answers
120
views
Configure MKS Robin WiFi Module on FLSUN Super Racer without Klipper
I recently purchased an MKS Robin wifi module for my spouse's FLSUN Super Racer after noticing that the printer runs on an MKS Robin Nano V3.1 board. Immediately after installing the chip, I saw it ...
1
vote
1
answer
112
views
TPU on Ender 3 S1 Pro only works when flow is set to 600 %
First time trying the EasyPrint Flex TPU filament. When printing a solid, I can see clear lines with plenty of air on both sides. This gives me the idea that it is not extruding enough filament.
I've ...
2
votes
0
answers
67
views
Klipper can't find config files
I reinstalled Klipper with kiauh due to other issues I had.
The folder klipper_config is still filled with all important config files and all G-code data is there ...
1
vote
0
answers
113
views
Bigtree GTR V1.0 + M5 (Klipper) Can Klipper access my M5 expansion board?
Just a quick question, Does Klipper support Expansion Boards?
0
votes
2
answers
1k
views
Creality Sprite Extruder custom install on Ender 3 Pro with TMC2208 and Klipper
I'm trying to set up a Creality Sprite Extruder on my Ender 3 Pro without using the kit (installing the extruder alone).
I can see here that the extruder operates at 1.4VDC and 0.8A.
I'm using TMC2208 ...
3
votes
2
answers
828
views
Klipper: power on before homing
I'd like to force Klipper to perform power on (using M80) before homing. For this purpose I'm trying to override G28:
...
2
votes
1
answer
3k
views
What is the difference between Linear Advance and Pressure Advance
I've been trying to do some research on Linear Advance (LA) on Marlin and Pressure Advance (PA) on Klipper, and from my understanding the technology behind each is different, although also similar. ...
2
votes
1
answer
1k
views
Is it possible to store skew correction values in printer.cfg file in Klipper?
The Klipper documentation describes how I should apply skew correction:
Print the test model (I printed this 100x100x100 3-dimensional model)
Make the measurements (I have got about 0.5...0.6 mm ...
2
votes
1
answer
620
views
Klipper firmware on OctoPi asks for MCU for flashing
I have Marlin firmware on an Anycubic Vyper 3D printer and I want to use Klipper.
My Raspberry PI 3B runs OctoPi and I installed Klipper from Github. Now I want to flash Klipper, but when I select ...
2
votes
0
answers
264
views
Klipper on Ender 3 v2 wrong signals
I have very strange problem. Motors X and Z are messing up somehow. I mean if I try to home X only, Z moves also. And vice-versa. Y motor homes and moves normally.
Board is stock E3v2 v4.2.2 with ...
0
votes
1
answer
5k
views
"Unable to read TMC UART 'extruder' register IFCNT" - Klipper and Robin Nano
I'm trying to use software UART for TMC2209 steppers on a BigTreeTech v1.2 and apply that to my Robin Nano v.1.1 using Klipper firmware.
I declared a different pin for every driver and I edit my ...
2
votes
1
answer
2k
views
Steppers stuck with Klipper but work with Marlin
I replaced the fans of my ender 3v2 with Noctuas & Buck converters. During the replacement, I made a mistake and burnt the motherboard (shorted one of the fans). I replaced the motherboard, ...
2
votes
1
answer
1k
views
Klipper BED_SCREWS_ADJUST and SKEW_PROFILE interaction
Klipper lets you define a skew profile that is loaded / unloaded on demand during START_PRINT / END_PRINT macros called during printing of a sliced file. This seems to be the recommended way to apply ...
4
votes
1
answer
11k
views
Klipper doesn't seem to adjust Z after BED_MESH_CALIBRATE
My rig:
Ender 3
BLTouch
Octopi
Klipper
Solid bed mounts
I've updated my start G-code from Cura to include a G29 right after G28...