Questions tagged [knowledgebase]

For frequently asked questions or questions that discuss the basics of 3D printing.

Filter by
Sorted by
Tagged with
12
votes
2answers
9k views

What is a printer console/terminal?

I read that G-code commands can be sent through a console/terminal over USB. What is a console/terminal and how do you use that?
11
votes
2answers
53k views

How to center my prints on the build platform? (Re-calibrate homing offset)

When I print large prints close to (but not exceeding) the maximum dimensions of the heated build platform on my Anet A8, the brim or skirt or the print itself is printed outside the heated bed, while ...
15
votes
1answer
38k views

How to set Z-probe boundary limits in firmware when using automatic bed leveling?

In setting up a probe for automatic bed leveling, the limits of the probing area must be entered in the firmware of a 3D printer. When using a sensor, how do you define the bed limits for the sensor ...
16
votes
2answers
27k views

What is Thermal Runaway Protection?

What is Thermal Runaway Protection (TRP) and why should I enable it? How does one do so in Marlin?
1
vote
1answer
14k views

Updating Marlin Firmware - Step by Step Guide

Note: This question is meant as a wiki to include all steps that are needed to update your printer with a self configured Marlin firmware version. The answer is a wiki that is currently in development ...
22
votes
4answers
57k views

What glues for bonding printed PLA to injection-molded plastic?

I will be creating a small tube styled piece to use as a junction between two pieces of plastic. The idea is to reattach the two pieces and provide strength so they don't break apart again. I plan on ...
3
votes
2answers
3k views

M502 will reset all configurable settings to their "factory defaults", which settings are those?

From the M502 documentation page can be read that M502: Reset all configurable settings to their factory defaults. Please ...
9
votes
1answer
3k views

Slicer line width vs. extrusion multiplier for layer adhesion?

My question would like to address what would be better for adhesion and general quality and possibly strength: either increase the slicer line width option or increase the slicer extrusion multiplier ...
4
votes
2answers
821 views

What special considerations must be taken when designing parts for 3D printing?

What are the 'headline' basic design rules for FDM? Which topics for design principles do you recommend to someone who has purchased an FDM machine and wants to understand what is practical? In ...
22
votes
5answers
11k views

Should I enclose my 3D Printer?

I have a home built RepRap with all sides open.. Would there be any advantage to enclosing the print area in acrylic?
8
votes
2answers
621 views

3D printing references for beginners

I have just received a 3D printer for Christmas (Robo R2). I am confused by the sheer amount of settings that I can tweak and I'm hesitant to do so until I know more about them. I was wondering if ...
5
votes
2answers
6k views

How to calculate the proper layer height multiples?

We all know, that the best layer hight is, when you have multiples of full steps. If it is not, sometimes steps get skipped and end up bad layer-to-layer adhesion when one height step missed a tiny ...
5
votes
1answer
4k views

What is the functional difference between an e3D-Style nozzle, Makerbot MK8 and M6 Chinesium Nozzles?

There is pretty much an ecosystem of two Nozzle designs out there that share the M6 thread on the coupler to the Heating block: the e3D "snub nose" or "shouldered" design. the "Chinesium" nozzle ...
13
votes
4answers
28k views

Why is it conventional to set line width > nozzle diameter?

I recently became curious about the Line Width setting in Cura and why one might change it if they aren't using different size nozzle. Since I've gotten my Ender 3, I've always kept the line width ...
1
vote
1answer
696 views

How do I know if a filament is abrasive?

There are tons of fancy filaments around. And a lot are super nice to look at or have super cool properties, like carbon-filled nylon being comparatively far stronger than other material, wood fill is ...
15
votes
2answers
15k views

How may I identify the firmware in use on my 3D printer?

I have a generic printer with no support documentation. How do I determine what firmware is in use so that I can research how to make the print run?
8
votes
2answers
3k views

How to pause a print to insert something in a cavity using Ultimaker Cura?

I have a model that contains a cavity, into which I want to insert a piece of metal, so I can use a magnet to stick to the print. How can I introduce a pause into the G-code without manipulating it ...
1
vote
1answer
16k views

How to activate Power Loss Recovery in Marlin?

Standard Marlin has one problem: when the power suddenly is gone, the print is gone. Prusa and many china printers however come with "Power Loss Recovery" or "Power Out Protection" or similar. But ...
6
votes
7answers
5k views

Fix ghosting problem (damping versus bolting printer to a desk)

I have a Monoprice Maker Select v2. It is the kind where the moving plate (heat bed) provides the Y-axis and the moving extruder provides the X-axis. It has a fairly rigid sheet metal frame. In ...
11
votes
2answers
20k views

How to choose an extrusion temperature?

From what I've been able to find out, online sources recommend around 205ºC for PLA and around 240ºC for ABS. But these are only guidelines, of course. Optimal printing temperature can be different ...
1
vote
2answers
168 views

How to replace the nozzle in my hotend assembly?

What should I take care of to replace the nozzle of the hotend assembly the right way? What kind of data, precautions, tools, steps, and verification are important for replacing the nozzle? The ...
8
votes
3answers
514 views

Are there any "best" or at least "common" practices to handle allowances in OpenSCAD code?

I'm designing a few mechanisms with OpenSCAD, and one of the parameters that need adjustment between printers/filaments is allowances between pieces that need to be assembled together (for example, if ...
7
votes
1answer
4k views

Using auto-bed leveling, do I need to initiate G29 before every print?

Various methods to scan the top surface exist to improve the bed adhesion to prevent prints to come loose from the bed during printing: e.g. BLTouch and clones or inductive and capacitive sensors/...
5
votes
2answers
15k views

What causes "ghosting"?

I am printing some minion chess pieces for my teacher at school and on every model I have found something called "ghosting", or at least I heard that is what it is called. For example there is a strap ...
5
votes
2answers
166 views

Which software do I need to start print something?

I'm still new to 3D printing and I want to print something. I expect that I'll mess it up since I find nothing to adjust it but it is now laying around for 4 months and I'm sick of it. So my question ...