Questions tagged [mks]
The mks tag has no usage guidance.
15
questions
0
votes
0
answers
23
views
Sensor can not read temperature
I have MKS TinyBee board recently purchased. The temperature sensor reading gives either 'Err' or '0'.
I have tried all possible sensors in the Marlin table configuration, but still none of them ...
0
votes
1
answer
44
views
MKS-SBASE V1.3 Marlin Stepper Motor Current
I have an MKS-SBASE V1.3 with integrated stepper motor drivers, but they don't have a physical way to change the current. I know there is a way to update the DRV8825 stepper current through Marlin, ...
3
votes
1
answer
417
views
How to add custom physical buttons to a 3D printer in Marlin software
I have a 3D printer with MKS Robin mainboard + TMC2209.
How do I add a piece of code to Marlin, for example, to make a physical button to start preheating, etc. I would like to use the existing ...
2
votes
1
answer
155
views
Stepper motor driver dead?
I own a cheap 3D printer FLSUN Delta, which was bought 6 years ago. Several structural and other upgrades were done, such as additional frame links, a new heated bed with external MOSFET.
In the past ...
1
vote
1
answer
891
views
Error "TMC2208 or TMC2209 on Z2 requires Z2_HARDWARE_SERIAL or Z2_SERIAL_(RX|TX)_PIN
I am getting this error when I try to enable the Z2 driver for MKS Gen L V2.1
Could anyone help?
Error "TMC2208 or TMC2209 on Z2 requires Z2_HARDWARE_SERIAL or Z2_SERIAL_(RX|TX)_PIN.
1
vote
0
answers
93
views
How to enable Z-offset on MKS TFT28 V4.0
I am trying to enable Z-offset on MKS MKS TFT28 V4.0 touch screen but I couldn't for some reason.
This is the code that I have uploaded to the Screen firmware in which you can see that I have enabled ...
3
votes
1
answer
1k
views
Stepper Motors getting extremely hot
I installed MKS Gen L V2.1 with TMC 2209 drivers to my Creality Ender-3 printer and updated the software to marlin 2, the stepper motors are getting extremely hot. What should i due to resolve this ...
1
vote
0
answers
53
views
MKS / Bigtree Closed Loop stepper the same?
Is the MKS and BigTree closed loop stepper the same? I see more responses to BigTree question. I read BigTree was plug and play and seems to be getting good support from them. I'm using the MKS ...
1
vote
1
answer
182
views
Mixing (closed loop) stepper drivers on MKS main board
Can I mix BIGTREETECH S42B closed loop stepper drivers on the MKS Gen L controller board with other drivers?
Are the pins in the same position? Would mixing work?
1
vote
0
answers
803
views
Anycubic Kossel Delta switch from Trigorilla to MKS Gen L 1.0
I have an Anycubic Kossel Delta 3D Printer.
The original Trigorilla motherboard died and I decided to buy one but I only found a Makerboard MKS Gen L 1.0 which is said to be compatible with Trigorilla....
1
vote
1
answer
1k
views
Connecting (Anet A8) 2004 display to MKS GEN L V2.0
Although it seems this question has been answered before Connecting (Anet A8) 2004 display to MKS GEN L this one differs because the v2.0 board has no obvious AUX-2 connector.
So the question is, how ...
2
votes
1
answer
148
views
Marlin 1.0 works: Marlin 2.0 destroys Z-axis motion
I have an FLSun 3D Cube, running off an MKS GEN V.1.4 main board. With Marlin 1.0, the Z-axis works great (and has been for three years). When I try to upgrade to Marlin 2.0, moving the Z-axis 10 mm ...
2
votes
1
answer
199
views
Thermal runaway
I have a bit of a headache with my Anycubic i3 Mega which originally had a Trigorila 32-bit board.
I decided to swap it because of loud A4988 drivers and got myself an MKS Robin Nano 1.2.
This printer ...
3
votes
0
answers
208
views
Retraction fine but recovery occasionally just doesn't happen
I'm having issues with retraction. My printer prints very well normally, but has an intermittent problem with retraction: the retraction itself always happens, but sometimes the subsequent recovery ...
2
votes
2
answers
6k
views
How can I print to my FLSUN QQ over Wi-Fi?
I want to be able to control my FLSUN QQ over Wi-Fi and don't have OctoPrint or a Raspberry Pi to run it on.