Questions tagged [monoprice-maker-select]

Questions using this tag should involve a 3D printer that is manufactured by Monoprice and branded by the name Maker Select 3D Printer v1/v2.

Filter by
Sorted by
Tagged with
3 votes
2 answers
2k views

I can't level my bed any more

I have a Monoprice Select v2 that I just bought less than 2 months ago. I've manually leveled it on several prints prior. I noticed a couple of holes in my print bed after my last print, like the ...
user avatar
  • 459
8 votes
1 answer
4k views

How to eliminate stringing and regulate flow rate?

I have been having a problem with stringing on my 3D printer, so initially I increased retraction distance from 6.5 mm to 8 mm. Then I tried again, with the same issue, so I increased ...
user avatar
  • 195
5 votes
2 answers
6k views

Apparently systematic nozzle clogging

A Monoprice Maker Select V2, upgraded incrementally with a Micro Swiss all metal hot-end, machined lever, and D4 extruder gear, systematically fails to produce complete prints, as seen below: The ...
user avatar
  • 509
5 votes
2 answers
3k views

How do I calibrate the temperature of my hotend?

I'm using a Monoprice Maker Select v2 (a Monoprice-branded Wanhao i3 duplicator) and would like to calibrate temperature readings for my hotend. I used a thermal probe on my multimeter to determine ...
user avatar
  • 202
5 votes
1 answer
152 views

What is this part and does it have to do with my my z-position is messed up?

I recently bought my first 3d printer, a monoprice maker select v2. After a couple of print jobs, this piece fell out. I have no idea where it came from. But afterwards, I notice that my Z-...
user avatar
  • 459
5 votes
3 answers
909 views

What tweaks do slicers use to get rafts to stick?

I've always had trouble getting prints to stick directly on my bed, but had great reliability when use rafts. This didn't present a problem when I was using PLA, but I recently got a roll of PETG and ...
user avatar
  • 151
4 votes
1 answer
527 views

Why does my model stop printing at the same spot?

I have a Monoprice Maker Select v2 printer which has a printing height of 7". I tried to print this trophy. The first time I printed, it stopped about 3/4 of the way (about 5.5"). I use Ultimaker ...
user avatar
  • 459
3 votes
2 answers
288 views

What do you recommend for removing prints from Monoprice Maker Select bed?

I've been making some ABS prints, but it's really hard to remove it afterwards. I've read a lot of different ways of removing it, including using the included chisel/spatula, using air duster, 50/50 ...
user avatar
  • 459
3 votes
6 answers
2k views

What do you use to keep your blue tape from lifting?

I have a few issues with the blue tape, which I'm trying out for the first time. The tape seems to warp, bubble and lift from the aluminum plate when it heats and cools and during printing. I put ...
user avatar
  • 459
3 votes
4 answers
565 views

What causes this "stringing" and can my print recover from this?

Here's what it looks like This is the model thingiverse linky It looks like it couldn't print the edge, but this happened many many hours after printing the brim. This did not happen with my 1st ...
user avatar
  • 459
2 votes
1 answer
204 views

Adhesion problem when printing calibration test

Here is my first attempt at printing a "Bed Leveling Calibration test". It obviously didn't come out as I would have hoped, but what can you say just looking at this picture? Is it possible to tell ...
user avatar
  • 459