Questions tagged [nozzle]

Questions about an extrusion assembly's nozzle component

15 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
6
votes
1answer
357 views

Makerbot Smart extruder+ heat block and nozzle question

I am looking for information on the smart extruder+ heat block and nozzle? I have looked online and from several forums come to the conclusion it is either a MK10 or MK11 assembly. Can anyone shed ...
2
votes
0answers
36 views

Silicone socks for nozzle only?

Is there a readily available silicone sock that goes just over the nozzle, to supplement an existing sock around the heat block body? I've seen a product for the E3D V6 that goes around the entire ...
2
votes
0answers
60 views

Path of a nozzle crosses over itself

I built my first printer couple of days ago. I started printing small models (20x20 mm max.) and everything was alright at first. However, when I tried to print a bit larger models, I started ...
1
vote
1answer
62 views

Z-Probe height isn't working

I just upgraded my CR-10 to a 32-bit board with Marlin and a BLTouch for bed-leveling. Here is my process: Run bed-leveling and save setting to EEPROM Make sure that software end-stops are off with <...
1
vote
0answers
20 views

Any method that I can refer to simulate 3D scanning and flow through extruder in MATLAB?

I would like to simulate the 3D scanning process with a specific wavelength and swath width of the beam, etc. and then reproduce the image, the whole of which in MATLAB. I also want to simulate the ...
1
vote
2answers
611 views

My nozzle on my Ender3 V2 is higher when it is printing than it is when I auto home it

I just got a new Ender3 version two for Christmas and was very excited to use it so I put it together and used the sample filament that came with the printer and everything worked okay for a bit. That ...
1
vote
0answers
222 views

Creality CR10 S5; the Z dimension is wrong after switch from 0.4 to 0.2 mm nozzle

So I tried to print a model with a 2 mm thickness main area, and a couple 4 mm parts that stick out. Instead the 4 mm is 3.05 mm and the 2 mm is 1.07 mm (0.042 inches ...
1
vote
2answers
8k views

E3D V6 nozzle vs MK8 nozzle, first layer adhesion

Does anyone notice that when they upgrade from an MK8Makerbot(?) to a E3D V6 hotend that when using the same settings and bed-leveling/z-distance-setting procedures, that the filament is much more ...
0
votes
0answers
23 views

Ender 3 Pro stopped and not heat up

While taking a print today, the Ender 3 Pro suddenly stopped. I tried to restart printing, but the heater cartridge does not heat up. I tested the thermistor and it senses heat. Next, I checked the ...
0
votes
0answers
76 views

Ender 3 nozzle moves through previous layer on lithophane

I'm trying to print lithophanes and having an issue with the nozzle moving through the previous layer and basically "drawing" through the print. I've printed 3 lithophanes before with zero ...
0
votes
0answers
37 views

Anycubic Mega S 3D printer: Filament is not exiting the nozzle correctly when printing

I have this weird problem with my brand new Anycubic Mega S. First of all I use the default "Normal 0.2" setting in Ultimaker Cura 4.8 and I am trying to print this *MICRO* All In One 3D ...
0
votes
0answers
44 views

What tolerance class does E3D uses for their metric thread nozzles?

As we know E3D nozzles use M6 threads. These are metric threads, so they've different tolerance classes but which tolerance class are they using?
0
votes
0answers
309 views

How to remove a stripped nozzle

A few months ago I got an Ender 5 printer. After a few successful prints with only PLA, I started getting a lot of issues. The last time I came back after an hour and there was just a bird's nest ...
0
votes
0answers
2k views

Ender 3 overshot the set temperature and hitting MAX TEMP error

So for the past few months I have been printing in my Ender 3 and everything ran smoothly. But suddenly a few days ago I tried to print and the hot end temperature just keeps on rising past the set ...
0
votes
0answers
314 views

Too long time to wait for M109 to stabilize when changing extruders

I would like to kindly ask for some advice. I've got 2 extruders and 2 nozzles, they are working fine. I'm printing from Ultimaker Cura 4.1 generated files. I have problems with temperature ...