Questions tagged [print-axis-offset]
The print-axis-offset tag has no usage guidance.
13
questions
2
votes
0
answers
34
views
Marlin + BLTouch layer compression
I have an Ender 3 Pro which I recently added an SKR Mini E3 v2.0 with Marlin and BLTouch. I have run into an odd issue where roughly the first 10 mm of the print are compressed into ~7 mm of Z height....
3
votes
0
answers
85
views
Problem setting home and getting Ender 3 basic geometry dialed in
I have the following hardware configuration:
Ender 3 Pro
SKR E3 Turbo
Ender Extender 400XL
BLTouch
BTT TFT35 E3 v3.0 (Marlin/LCD and BTT/BLTouch configured)
Dual Z steppers (per Teaching Tech, ...
1
vote
0
answers
84
views
How to enable Z-offset on MKS TFT28 V4.0
I am trying to enable Z-offset on MKS MKS TFT28 V4.0 touch screen but I couldn't for some reason.
This is the code that I have uploaded to the Screen firmware in which you can see that I have enabled ...
2
votes
0
answers
111
views
Should center point of G29 matrix always be zero?
Questions:
Should repeated applications of G29 (auto-level) result in the same matrix as long as nothing is loose or has otherwise mechanically changed?
Should ...
0
votes
2
answers
145
views
Ender 3 - X Axis Cannot Reach True Home
After a year of printing smaller models, I finally went to print something that would take up most of the build plate from left to right and realized that my nozzle cannot reach "true" X ...
1
vote
2
answers
1k
views
How do I set my Z offset?
After watching every possible YouTube video on the subject and reading any source available, and although I'm a PhD and quite computer savvy, I still can't make my Anet A6 (no probe) behave in terms ...
0
votes
0
answers
137
views
Help coding the MIN_POS and x/y probe offsets
I've read a lot of posts in regard to these subjects but I think that the advice is just so saturated it's hard to know what to follow.
I've had trouble with my bed min pos and x/y probe offsets ever ...
0
votes
1
answer
794
views
What is the correct Marlin firmware setting for Tevo Tarantula with MKS Base V1.2 board
I am trying to correct the x&y offsets in the Tevo Tarantula that I got from a friend in order that my printer is not printing over the end.
What I got so far is that I need to measure and then ...
0
votes
1
answer
131
views
Z-offset issues with Slic3r and Da Vinci Nano
I was attempting to use Slic3r 1.3.0 to print to my Da Vinci Nano, using MiniMover (a replacement for xyzprint) to load the G-code.
The print seemed to be a couple of millimeters off of the bed, but ...
1
vote
1
answer
11k
views
Creality Ender 3 X axis homing issue
I bought an Ender 3 recently. Auto-home is on the right front moving away from the end stop. I did reverse the wiring of the X axis motor, it did not work. I had Marlin 2.x uploaded, it didn't work ...
0
votes
0
answers
139
views
Z level babystepping works inconsistently after BLTouch was installed
After I installed the BLTouch sensor, the manual adjustment of the Z offset is unreliable. I found that for it to work, the software endstops must be disabled. If they are enabled, the nozzle won't ...
7
votes
1
answer
6k
views
Marlin "Tune->Bed Z" vs "Tune->Babystep Z" vs Z Offset?
What is the difference between:
Tune -> Bed Z
Tune -> Babystep Z
Control -> Motion -> Z Offset
And when are you supposed to use "Bed Z"?
1
vote
2
answers
232
views
Do you have trouble with 3D printer on UPS during short power outages?
Using a Gearman RepRap with Slic3r, printing from an SD card, with an uniterupted power supply (UPS), and both PLA and ABS filaments, short power outages often result in x/y-axis offsets (see image). ...