Questions tagged [print-axis-offset]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
0
votes
1answer
72 views

Z-offset issues with Slic3r and Da Vinci Nano

I was attempting to use Slic3r 1.3.0 to print to my Da Vinci Nano, using MiniMover (a replacement for xyzprint) to load the G-code. The print seemed to be a couple of millimeters off of the bed, but ...
0
votes
0answers
714 views

Ender 3 Pro: How to solve the issue with different Z-offsets?

I have an Ender 3 Pro with BLTouch (original) and did at least a dozen of test prints to adjust everything (steps/mm, ...). I did everything at the target temp of PLA. But I've still got the problem ...
1
vote
0answers
19 views

How to enable Z-offset on MKS TFT28 V4.0

I am trying to enable Z-offset on MKS MKS TFT28 V4.0 touch screen but I couldn't for some reason. This is the code that I have uploaded to the Screen firmware in which you can see that I have enabled ...
2
votes
0answers
82 views

Should center point of G29 matrix always be zero?

Questions: Should repeated applications of G29 (auto-level) result in the same matrix as long as nothing is loose or has otherwise mechanically changed? Should ...
0
votes
1answer
39 views

Ender 3 - X Axis Cannot Reach True Home

After a year of printing smaller models, I finally went to print something that would take up most of the build plate from left to right and realized that my nozzle cannot reach "true" X ...
1
vote
2answers
272 views

How do I set my Z offset?

After watching every possible YouTube video on the subject and reading any source available, and although I'm a PhD and quite computer savvy, I still can't make my Anet A6 (no probe) behave in terms ...
0
votes
0answers
43 views

Help coding the MIN_POS and x/y probe offsets

I've read a lot of posts in regard to these subjects but I think that the advice is just so saturated it's hard to know what to follow. I've had trouble with my bed min pos and x/y probe offsets ever ...
0
votes
1answer
300 views

What is the correct Marlin firmware setting for Tevo Tarantula with MKS Base V1.2 board

I am trying to correct the x&y offsets in the Tevo Tarantula that I got from a friend in order that my printer is not printing over the end. What I got so far is that I need to measure and then ...
1
vote
1answer
7k views

Creality Ender 3 X axis homing issue

I bought an Ender 3 recently. Auto-home is on the right front moving away from the end stop. I did reverse the wiring of the X axis motor, it did not work. I had Marlin 2.x uploaded, it didn't work ...
0
votes
0answers
110 views

Z level babystepping works inconsistently after BLTouch was installed

After I installed the BLTouch sensor, the manual adjustment of the Z offset is unreliable. I found that for it to work, the software endstops must be disabled. If they are enabled, the nozzle won't ...
7
votes
1answer
4k views

Marlin “Tune->Bed Z” vs “Tune->Babystep Z” vs Z Offset?

What is the difference between: Tune -> Bed Z Tune -> Babystep Z Control -> Motion -> Z Offset And when are you supposed to use "Bed Z"?
1
vote
2answers
178 views

Do you have trouble with 3D printer on UPS during short power outages?

Using a Gearman RepRap with Slic3r, printing from an SD card, with an uniterupted power supply (UPS), and both PLA and ABS filaments, short power outages often result in x/y-axis offsets (see image). ...