Questions tagged [prusa-i3]
The Prusa i3 is the third iteration of Josef Průša's RepRap 3D printer design. This is an open-source design, the tag should be used regardless of individual manufacturer. You might want to add the specific manufacturer or model as a separate tag.
279
questions
1
vote
1
answer
129
views
Can I use PT1000 thermistor on my Prusa mk3s+ without installing Klipper on it?
I recently bought a High-Precision (400 °C) Revo Hotside with the intention to use it on my upcoming Voron. In the meantime, I wanted to give it a go and use it on my Prusa, if for nothing else, then ...
1
vote
0
answers
53
views
What issue can make very short temperature spikes to appear?
I have issues with momentarily temperature spikes, but only above 250 °C. At and below 250 °C it's pretty solid.
I'm using Prusa MK3s+ with a E3D Revo upgrade.
I suspected connector issues as ...
4
votes
1
answer
98
views
What could have caused both belts becoming loose?
Recently both belts on my Prusa MK3S+ became loose. Quite suddenly, too. One print was okay, the next nozzle wobbled in the Y and bed in the X causing layer shifting. More precisely, each movement was ...
2
votes
1
answer
43
views
Is it safe to use 230 V AC, 10 A relay shield to turn my Prusa MK3S+ on/off using OctoPrint?
Prusa says the MK3S+ draws up to 120 W. So let's say 150 W of inrush current.
$$150 W \div 230 V ≈ 0.65 A$$
An order of magnitude less than a typical Raspberry Pi optically isolated relay shield can ...
2
votes
0
answers
16
views
How to polish heatbreak surface?
I have a plastic squeezing up from the heatbreak thread. This indicates improper seal, but I have screwed everything together tightly. After disassembly, I realized I have a scuffed surface on my ...
5
votes
1
answer
60
views
What material is Prusa mk3s+ hotend heaterblock made of?
My heaterblock is in a poor state after the heater malfunction. Before I'll buy a spare, I want to ask what material is the original block made of? I don't see it on the product page.
Available spares ...
0
votes
0
answers
18
views
3D printer X-axis sometimes binds up whilst printing
My MK2s has developed a strange problem where the X-axis will bind up whilst printing. This causes it to layer shift. The strange thing is I can move the X-axis manually. It doesn't bind up and feels ...
0
votes
2
answers
58
views
Prusa i3 MK2 thermistor connector reference
I think my heat bed thermistor is broken (infinite resistance measured) on my Prusa MK2, so I bought a new one, and I'd like to know which connector I shall use. Where can I find the references of ...
1
vote
0
answers
23
views
Prusa I3 MK2s with tilt in the X and Y directions
So I converted my Prusa MK2S to use Duet electronics. I have always had problems with bed leveling. It doesn't appear to help much if any.
So I can complete a bed probing session but the result is ...
0
votes
2
answers
115
views
Issue with PETG adhesion
I am printing on a Prusa i3 MK3 with white PETG and I face several issues when it comes to the extruder shaping the bridge and solid infill. For the record, the temperature is set at 230 °C for the ...
0
votes
0
answers
50
views
First layer issue with new filament
My settings were fine but after switching to a new brand of PLA I seem to be getting issues with the first layer.
My previous filament had a print temp between 200 °C and 230 °C. My current settings ...
1
vote
1
answer
39
views
Starting 3D printing at home [closed]
I've been doing some 3D printing at work as a means of different tool holding devices and jigs and from this time I have gained some, although very basic, knowledge on how the printers work and how to ...
0
votes
1
answer
32
views
Prusa MK3s+ potential extrusion problem
I've recently tried printing something I've printed multiple times but this time it isn’t printing much at all. It seems to inly be printing a very small film of filament rather than a solid layer in ...
0
votes
1
answer
40
views
Prusa MK3s+, Prusa PETG 1.75mm filament
I encountered a case of pillowing throughout several layers that was very severe, however, I managed to fix it through adjusting the temperatures but I was wondering if anyone could tell me if there ...
1
vote
1
answer
1k
views
Octoprint does not detect Serial port of RPi zero
I am following the tutorial of Prusa for using Octoprint with my Prusa i3 MK3. I have a Raspbery Pi Zero and I'm using the built-in GPIO pins, not an USB connection.
Wifi works. I can reach the ...
0
votes
0
answers
36
views
MMU2S continued print after filament swap faillure
I had an odd failure case today. I've been trying to print a successful model with my newly installed MMU2S on a MK3S+ - specifically this one which seems to be a popular first print.
https://www....
4
votes
1
answer
421
views
Is a 40x20 Noctua fan with a shroud good for part cooling?
I am having a lot of troubles with running my Prusa Mk3S at my student dorm, because of the extremely loud stock part cooling fan - it annoys people A LOT). So I started working on a design using one ...
3
votes
2
answers
500
views
Drying filament with heated bed on Prusa - how to "bypass" safety timer?
On my Prusa MK3, I'm trying to make a G-code that only heats up the print bed and moves the Z-axis up and down a little bit every 20 mins to prevent the safety timer going off. This is what I have ...
2
votes
1
answer
4k
views
How to adjust vase mode thickness
I am new to 3D printing, and are having a problem with wall thickness in vase mode.
I would like to print this vase model: https://www.printables.com/model/60696-blossom-vase
As seen in the "...
2
votes
0
answers
121
views
Weird infill edge problem
I'm having this weird issue; for some weird reason, the infill pattern starts separating from the walls and over time, the print becomes a mess. As it separates, it starts to curve, and you get this ...
3
votes
2
answers
1k
views
Prints coming out with jagged lines on the sides, rough edges
I am pretty new to 3D-printing, and I have just finished assembling my Prusa i3 a few days ago.
I finished up basic calibrations, which went fine, but noticed my prints were coming out with a bunch of ...
0
votes
1
answer
148
views
My extruder failed. Is there any hope to recover print? [duplicate]
Yesterday I had filament that entangled on the spool and before I knew it, the printer told me to eject the filament. Unfortunately, then the filament broke. There is no way to fully unload it, no way ...
1
vote
1
answer
855
views
Vertical holes: round vs hexagonal
Please reference the following page on Thingiverse:
https://www.thingiverse.com/thing:5600770
This is an insert for a bandsaw (the replaceable part that the blade passes through in the middle of the ...
4
votes
1
answer
3k
views
What are viable substitutes for Raspberry Pi to run Octoprint or similar software for Prusa i3 MK3S+?
Where I live, Raspberry Pi is currently* either unavailable, at prices 3 times higher than a year before, or sold online as "untested". Or straight up as not working. So I am not getting one....
2
votes
3
answers
258
views
How can you print Prusa MMU2S at home?
I want to buy my first FDM printer, to print household items and wearable gadgets too big for my LCD resin one. Due to financing & tax reasons, what I'll buy now is what I will have for at least a ...
0
votes
0
answers
55
views
Prusa i3 MK8 can't achieve required temperature
I've just installed a new 12 V hotend for my Prusa i3 MK8. So, now the new hotend can't achieve temperatures above 190-200 °C and it takes about 30 minutes to achieve 200 °C. The thermistor and ...
1
vote
1
answer
3k
views
Seams of print are underextruded causing large pits/gaps? (Prusa Mk3+, Prusa Slicer)
The seams on my print are much larger than they were a few months ago and I'm not sure what's going on or how to fix it.
Pic with seams random:
With aligned seams:
I'm using the 0.2 mm QUALITY ...
3
votes
1
answer
270
views
Using 40W adapter on 30W heater cartridge?
Recently, I accidentally shorted out my heater cartridge when trying to do my first nozzle swap on my Prusa MK3S+. I just ordered a new E3D v6 Hotend with 30 W Heater Cartridge and it will be here in ...
3
votes
2
answers
159
views
How can a speaker or active buzzer be connected to the Arduino 2560/RAMPS 1.4 boards to provide alerts in response to M300 commands in the g-code
My Prusa i3 does not appear to have any sound device incorporated. I've read "Writing G-Code: Audible Alert at end of print" and it seems everything needed to implement audible alerts is ...
1
vote
1
answer
78
views
How is the Prusa typical orange surface created?
Photos exist where the orange controller of Prusa printers is shown.
In most photos, it looks as if the surface is somewhat rough.
Here is such a photo:
It sparkles a bit, so I would assume that it's ...
4
votes
1
answer
695
views
Why is it more common to move the extruder on the Z-axis than the print bed, in consumer FDM printers?
Why is it more common for consumer level FDM printers to move the extruder on the Z-axis (For example, the Ender 3) while the bed remains at a fixed height, than to have a bed that moves up and down ...
2
votes
2
answers
119
views
Prusa i3MK3S+ layer skip with polycarbonate (overheating?)
On the last couple of polycarbonate prints with my Prusa, one or more layers have been completely skipped (i.e. no material extruded). The rest of the print is fine save some minor warping. I'm ...
5
votes
3
answers
2k
views
How to print a cylinder with hundreds of small holes?
I'd like to print a cylinder, 50 mm diameter, 200 mm long, with 1.5 mm diameter holes tightly fit like this:
The holes go all the way through from top to bottom.
I am using a Prusa i3 MK3S. With 0.1 ...
3
votes
1
answer
281
views
Marlin firmware issues
So I'm working on building a Prusa i3 MK3 clone and all's gone well so far but when I make edits to the firmware and reupload it, the printer doesn't seem to be getting it. Like I changed the software ...
0
votes
1
answer
184
views
Clearing persistent partial clog after printing nylon
My Prusa i3 MK3S printer experienced a partial clog last time I was printing with nylon.
Although I've experienced clogs and partial clogs before, all the usual tricks I've tried have not worked this ...
2
votes
1
answer
950
views
3mf circles are printing as polygons
When I'm using a .3mf file from Fusion 360 the circles are coming out as polygonal shapes that are very easy to see.
When using a .stl file from Fusion 360 the circles are near perfect the polygons ...
4
votes
0
answers
75
views
What does CRASH_RECOVER mean from Octoprint?
When watching the Raspberry PI daemon.log while running OctoPrint, I see contents like the following, which occasionally includes enqueing "CRASH_RECOVER" (but I do not see "...
2
votes
2
answers
3k
views
Distinguish i3 MK3 from i3 MK3S
I have a Prusa i3 MK3 or maybe it was upgraded to a i3 MK3S.
How can I figure out?
The description of the upgrade kit talks about
the SuperPINDA (how is it different from the old one?)
a number of ...
3
votes
3
answers
11k
views
Is enclosure without ventilation enough to keep VOC's and printer fumes from leaking into my room?
I am currently in the look for a 3D printer and one major issue I find it the fumes/VOCs that printing can emit. I am not planning to do ABS or similar but I've read from studies that PLA also may ...
3
votes
3
answers
2k
views
Prusa MK3S not extruding during printing but extruder working
I didn't have any printer-related problem for the past 6 months, but now all of a sudden my Prusa MK3S stopped extruding during printing.
This is very strange as I can easily load\unload filament and ...
1
vote
1
answer
630
views
Can a Prusa be converted to IDEX?
I have a Prusa i3 Mk3s with an MMU2s on it. And to be frank, as far as the MMU goes, I have not had much luck with it. I've seen people print amazing MMU prints and it works great for them, but I ...
1
vote
4
answers
490
views
Z-Axis on a winch
In Prusa i3 clones the Z axis is often problematic. Mechanically unsynchronized dual Z axises which are driven by the same stepper driver easily misalign. Using only one Z motor makes the whole gantry ...
0
votes
0
answers
32
views
Print stops midway and extruder collides with the frame while printer display appears frozen
I have a strange problem with my Hictop Prusa i3 printer. Recently almost all my prints fail midway (even small prints that were successful in the past). At some random location and time, the x and y ...
1
vote
0
answers
102
views
Horrid issues with printing with Anet A6?8?
I just recently got a printer, supposed to be a Prusa i3 Reprap clone. It came with Repetier firmware on it, and its previous owner had no idea about any calibration. I calibrated X-, Y-, and Z-axis ...
2
votes
2
answers
381
views
Which connector should I use between the power supply and the Einsy board?
I am looking for a way to easily separate the wires between the power supply and the Einsy board of my Prusa Mk 3S+ with a connector. The power supply delivers 10 A at 24 V.
I thought about a YL wire-...
4
votes
1
answer
455
views
How to unload filament without cancelling print
I have a Prusa MK3s MMU2s which I was running a 7-hour print job on.
It had two spools of filament in, a blue one (primary, very little left) and a gold one (secondary, quite a lot left). It ran out ...
2
votes
3
answers
744
views
Prusa MK3 heatbed shorted: replace just Einsy or heatbed too?
Prusa MK3 heatbed power cable shorted out (on the Einsy side) and it looks like I need to replace the Einsy. Should I replace the heatbed too? I don’t know electronics well and am worried I will just ...
3
votes
1
answer
524
views
Is it better use Nylon fillement for cold pull even if I have been using PLA?
Using Prusa I3 MK3S
I am using PLA fillement and I need to do cold pull from time to time.
I noticed many people on Internet suggestusing Nylon fillement for clod pull.
I wanted to reach out to this ...
1
vote
1
answer
401
views
Sudden deterioration of print quality on Prusa i3MK3S+
I've had my Prusa i3MK3S+ for a couple of months now, and done 100+ prints, and other than a few issues with first layer adhesion (which are pretty much solved now), have been getting consistently ...
2
votes
3
answers
2k
views
Ideas to tune for 300 % speed
I am using PLA and I am looking for ideas on using the Tune option to tune my Prusa i3 MK3 to increase the speed to 300 %.
The 300 % speed works perfectly fine for ...