Questions tagged [prusa-i3]

The Prusa i3 is the third iteration of Josef Průša's RepRap 3D printer design. This is an open-source design, the tag should be used regardless of individual manufacturer. You might want to add the specific manufacturer or model as a separate tag.

17 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
7
votes
0answers
83 views

Marlin 2.0 Firmware temperature jumping on LCD when trying to configure UBL

Flashed Marlin 2.0 on my Folgertech 2020 Prusa i3 variant. Calibrating seems to have gone smoothly until I tried to set up UBL. Saved the mesh into EEPROM with the ...
2
votes
0answers
17 views

What does CRASH_RECOVER mean from Octoprint?

When watching the Raspberry PI daemon.log while running OctoPrint, I see contents like the following, which occasionally includes enqueing "CRASH_RECOVER" (but I do not see "...
2
votes
0answers
75 views

Prusa MK3S Nylon&ABS print failures

I'm using Prusa i3 MK3S and every time I want to create a durable, impact resistant part, I use ABS/Nylon. The problem is, however, that when I print something small (of less than 1 cm width for ...
2
votes
0answers
509 views

Geeetech Prusa I3 Pro W. Cannot update firmware

Initially when I built it, it turned on and the LCD worked. I had an issue with the Z axis but I think that's unrelated to my current issue. The next day when powering on the LCD just showed black ...
1
vote
0answers
44 views

Horrid issues with printing with Anet A6?8?

I just recently got a printer, supposed to be a Prusa i3 Reprap clone. It came with Repetier firmware on it, and its previous owner had no idea about any calibration. I calibrated X-, Y-, and Z-axis ...
1
vote
0answers
51 views

Print quality ruined after firmware update i3 mk3

I'll try to give as much detail as I know here but let me know if there is anything missing. I have a Prusa i3 MK3 that I got in about 2018 and it was working perfectly fine. Print quality was pretty ...
1
vote
1answer
34 views

CTC i3 Y-axis thin / no filament deposition

I have this CTC i3 printer; when I print square test prints, as it moves along the Y-axis back to zero (front). It extrudes lines but very thin or none at all. But opposite direction along the Y axis ...
1
vote
0answers
37 views

ETA for print job showing negative in Repetier host

I'm using Repetier host 1.0.6, and ever since adding default retraction settings, the "ETA" showing during a print job is negative: It stays this way throughout the print job, which is no fun, since ...
1
vote
0answers
69 views

Steps to setup a new 3D Printer

I hope it doesn't get closed since my question is widely open: I got recently a Geeetech Prusa i3 Pro B as a DIY kit, the assembly took a lot of time since the package did not include a building ...
1
vote
0answers
2k views

Where is .dxf file of this frame(Prusa i3)?

I am looking for this fram, but in github there is no download option for it! So I did copy the code and paste it, but in result when I measure the big frame's edges it shows bigger 9100mm !! but I ...
1
vote
0answers
258 views

ANet A8 Pre-Heat PLA Issue

When I go to Quick Settings/Pre-heat PLA, the computer dies the LCD screen goes blank the power supply makes weird noises and then about 2 minutes later, the LCD Screen goes back to the Printer Ready ...
1
vote
0answers
408 views

Prusa i3 Linux Mint Slic3r install problem

New to this domain, I got my prusa i3 last week and finished assemblage. Repetier params in Linux Mint 18 are ok too. I'm now trying to launch slic3r for the first time but I got this error launching ...
0
votes
0answers
24 views

Print stops midway and extruder collides with the frame while printer display appears frozen

I have a strange problem with my Hictop Prusa i3 printer. Recently almost all my prints fail midway (even small prints that were successful in the past). At some random location and time, the x and y ...
0
votes
0answers
41 views

Adjusting extruder

Since I have some problems with printing I wanted to try to adjust my extruder esteps. While changing the esteps I noticed that the value has almost no impact. My default setting was 93 and the ...
0
votes
0answers
185 views

Can't manage to force my print to standby while I insert a nut - Prusa Slicer and Tronxy XY2 pro

I use the Prusa Slicer on a Tronxy XY-2 pro which I believe uses RepRap firmware. I believe it uses RepRap firmware because I had to input it into the Prusa Slicer initialization questions, but I'm ...
0
votes
0answers
52 views

Help needed implementing Bear Upgrade

I am attempting to build a 3D printer using the Bear Upgrade for guidance. In this moment, I am implementing the X-Axis. The X_end_idler consist in two parts, the idler and the belt tensioner, as you ...
0
votes
0answers
268 views

Grayscale laser engraving with Ramp1.4

I have a Reprap Guru Prusa i3 v2 3D printer. To this I added a 5.5 W laser that I purchased online. The board of my 3D printer is an Arduino Mega 2560 board with Ramp 1.4. I have connected my laser ...