Questions tagged [repetier-host]

For questions regarding the repetier-host software used to send g-code commands to 3D printers

Filter by
Sorted by
Tagged with
2
votes
1answer
70 views

Low Accuracy while perfect travel movement

I own an older Anet A6. Flashed the Marlin Firmware on it (and think I configured it properly). Also updated to the latest 2.0.5.3 some days ago). The nozzle is a 0.4 mm one, direct drive ...
2
votes
1answer
68 views

Marlin 2.0.x bugfix 2nd extruder not working

I am using the SKR PRO board on a dual extruder 3D printer. I have tried Curaengine and Slic3r in Repetier-host. The printer firmware is handling the offset fine (it prints in the right spot for ...
0
votes
0answers
24 views

Changing printspeed at any point

I'm using Cura in Repetier Host and i'm looking for a Plugin like Tweak at Z but it has to work at any point in the model, so that i can "paint" the modell with colors and when i'm slicing it, the ...
0
votes
1answer
181 views

How to connect a Geeetech Prusa I3 Pro B to Repetier-Host on mac

My y-axis is running in reverse and slamming into the front of the machine. This is not ideal for my needs. I need to connect to it with the Repetier-Host software to fix this, and in general. This ...
5
votes
1answer
41 views

Extra data appended to the Y values when issuing `M92` & `M500`

I am still trying to dial in my Anet A8. The Marlin firmware takes too long to scroll through the axis settings when I change them, so I use Repetier Host instead issuing ...
1
vote
1answer
192 views

How do Repetier coordinates setup work

I am using Repetier Host and Slic3r Prusa 1.36.2 - (the website says 1.2.9 is the latest version - however I don't believe this is the problem) . The printer is a Anet A3 With my current setup I am ...
4
votes
2answers
4k views

Anet A8 Calibrated but print sizes are wrong

Anet A8 printer, Github Marlin, Repetier Host, Cura slicer Just setting up printer and printed 20mm calibration cube from Thingiverse. X,Y,Z & E not too far off but not quite right (centre hole ...
4
votes
2answers
288 views

Is Repetier host able to do multi-material printing?

Can Repetier host run a multi-material printer such as the Prusa i3 MK2S?
1
vote
1answer
182 views

Prusa I3x and repetier host heat problems

I've saved settings in the slicer for pla and abs, set the default bed temp to 90 and extruder to 185. No matter what settings I select to print with, the bed temp sets to 110 and the extruder to 230 ...
5
votes
3answers
2k views

How should I go about printing easily removable rafts?

I have had a 3d printer for a while now, and I have a lot of the quality settings dialed in pretty well, but one thing that constantly bugs me is removing the raft from my finished prints. I am using ...
2
votes
1answer
175 views

How do I decrypt messages on my Repetier firmware?

I need to send a complex password to my machine. The machine needs to decrypt it and run it. I have not found enough resources for such an operation. More detailed description: I am developing a ...
7
votes
3answers
2k views

What causes gaps in small region fills and how to prevent them?

I saw this cool Nuka-Cola bottle opener. I made it: As you can see, nasty gaps have appeared in the text. What could've caused them? I am sure I set the filament diameter correctly. So why did ...
6
votes
1answer
2k views

Distortion calibration on XY plane in Repetier

I built a delta 3d printer (like a mini Kossel) and now I'm trying to calibrate it. I made all the horizontal and vertical bars myself with wood and I bought angle joints (between bars) made with 3D ...
4
votes
2answers
3k views

Bed leveling method not working with Repetier firmware 0.92.9?

I homebuilt a delta 3D printer (like Kossel mini) with a Z probe near the hotend with manual deploy and RAMPS 1.4 board: I configured the Repetier firmware with the online tool; All my endstops (...
7
votes
3answers
494 views

Repetier Host stops sending commands to printer when switching Windows user

I'm running Repetier Host v1.6.1 with Repetier Firmware v0.92.9. My computer is running Windows 7 Pro SP1, 64-bit. If I set a print going via USB then switch to another user (note: I do not log out),...
3
votes
1answer
5k views

Offset in X or Y axis

How can I set an offset in y or x axis so that I can move the position of my printed object. I have tried doing this with so many options in Repetier, and in Slic3r, and still nothing, please, have ...
3
votes
1answer
398 views

Prusa XI3 not printing correctly with Repetier Host

I have a HE3D Prusa XI3 Specs are linked here. Its came with a MK8 Extruder, and I ordered the 0.3mm nozzle with it. I have Repetier v.91 loaded onto the printer right now, and Repetier-Host v1.5.4 ...