Questions tagged [skr-v1.3]
The skr-v1.3 tag has no usage guidance.
15
questions
0
votes
0
answers
87
views
Hotend functioning inconsistently. PID completed normally, heating to quickly or not at all on print start up
I have a Xvico X1 printer which I had previously installed an SKR 1.3 on running Marlin, which was functioning normally.
For Christmas I got a BLTouch, a heated bed and a Raspberry Pi for it, so I ...
0
votes
0
answers
2k
views
Error:Printer halted. kill() called! SKR 1.3 TFT35 3.0
I am trying to fix the very last error on my printer (custom built).
Error:Printer halted. kill() called!
This error occures about 5-10 minutes into a print (XYZ ...
1
vote
1
answer
232
views
Auto bed leveling offset issue
I'm using an Ender 3 with a new upgraded board SKR 1.3 Marlin bugfix 2.0 auto bed leveling I use EZABL.
for the EZABL I followed their tutorial for Marlin 2.0 since I don't use the unified firmware.
...
0
votes
0
answers
205
views
Printer froze mid print, stepper motor driver and MCU extremely hot afterwards. MCU seems dead now (?)
A strange problem occured while 3D printing. I've been printing for a long time now, and I consider myself fairly expeienced. normally, with every problem I've encountered with my printers (Anet, ...
2
votes
1
answer
923
views
Will the TMC2130 V3.0 stepper driver work with the Ramps 1.6 Plus board?
I want to buy the board Ramps 1.6 Plus. The description in the link says that is compatible with the driver TMC2130, but I found that there are two versions soldered in SPI mode.
BIGTREETECH TMC2130 ...
1
vote
2
answers
692
views
How to have double extruder and double Z motor on a 5-driver board?
We are using the Board SKR 1.3 with the following pins:
...
1
vote
2
answers
688
views
Partial underextrusion in walls
I'm facing weird "pillars" of underextrusion on outer walls of my XYZ test cube.
On the pictures below I`ve printed PLA test cubes with a 0.4 mm nozzle, 0.2 mm height and 210/50 °C ...
1
vote
1
answer
2k
views
Switch nozzle contact probe auto leveling with Marlin 2.0
I have a Robo R1+ which uses the nozzle contacting the glass print bed to level the printer. When the print head strikes the bed the Z-min endstops open signaling that the bed is touched.
I recently ...
3
votes
1
answer
2k
views
What UART port to use for RPi GPIO pins on an SKR v1.3 board
I have a Bigtreetech SKR v1.3, and I'm trying to connect a Raspberry Pi to the board using the RPi's GPIO pins as opposed to using a USB connection because space is limited within the case of CR10S ...
0
votes
0
answers
56
views
LV8729 on kossel issues with print dimensions (steps)
I've installed the an LV8729 on a kossel, configured with SKR 1.3 and marlin 2.0 with all the jumpers configured in the same way for 16 micro steps for X Y Z axis. Everthing seems fine the printer ...
7
votes
1
answer
9k
views
How to wire P.I.N.D.A. v2 to an SKR V1.3 board?
I bought a BigTreeTech SKR v1.3 main board and a P.I.N.D.A v2 for my P3Steel MGN. Does anyone know to wire them together and which part in Marlin 2 do I need to change?
5
votes
2
answers
3k
views
Setting Junction Deviation in firmware has no effect
I have built a 3D printer with Marlin bugfix-2.0.x forked from github.
I am attempting to set the default value for junction deviation so that I don't have to change it through the printer's screen/...
4
votes
2
answers
2k
views
G28 ignoring Z-Probe X/Y Offsets
I recently installed a SKR 1.3 Board with a 3DTouch-Probe on my Creality Ender 3 Pro.
The probe works, G29 does its magic, but:
If i issue a plain ...
4
votes
2
answers
614
views
Getting wrong measurements on my Kossel Linear Plus after installing SKR 1.3 with Marlin 2.0
So I've switched the Trigorilla board in the printer with a SKR 1.3 with TMC2208 drivers and installed the latest Marlin 2.0, with a config based on this one. You can find the Configuration.h here, ...
4
votes
3
answers
179
views
Bigtreetech upload stalled after uncommented REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER
I recently bought a BigTreeTech SKR V1.3 and uncommented REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER and clicked the upload button but faced an error that says:
<...