Questions tagged [skr-v1.3]

The tag has no usage guidance.

Filter by
Sorted by
Tagged with
5
votes
1answer
7k views

How to wire P.I.N.D.A. v2 to an SKR V1.3 board?

I bought a BigTreeTech SKR v1.3 main board and a P.I.N.D.A v2 for my P3Steel MGN. Does anyone know to wire them together and which part in Marlin 2 do I need to change?
5
votes
2answers
2k views

Setting Junction Deviation in firmware has no effect

I have built a 3D printer with Marlin bugfix-2.0.x forked from github. I am attempting to set the default value for junction deviation so that I don't have to change it through the printer's screen/...
4
votes
2answers
591 views

Getting wrong measurements on my Kossel Linear Plus after installing SKR 1.3 with Marlin 2.0

So I've switched the Trigorilla board in the printer with a SKR 1.3 with TMC2208 drivers and installed the latest Marlin 2.0, with a config based on this one. You can find the Configuration.h here, ...
4
votes
3answers
161 views

Bigtreetech upload stalled after uncommented REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER

I recently bought a BigTreeTech SKR V1.3 and uncommented REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER and clicked the upload button but faced an error that says: <...
4
votes
2answers
1k views

G28 ignoring Z-Probe X/Y Offsets

I recently installed a SKR 1.3 Board with a 3DTouch-Probe on my Creality Ender 3 Pro. The probe works, G29 does its magic, but: If i issue a plain ...
3
votes
1answer
2k views

What UART port to use for RPi GPIO pins on an SKR v1.3 board

I have a Bigtreetech SKR v1.3, and I'm trying to connect a Raspberry Pi to the board using the RPi's GPIO pins as opposed to using a USB connection because space is limited within the case of CR10S ...
2
votes
1answer
737 views

Will the TMC2130 V3.0 stepper driver work with the Ramps 1.6 Plus board?

I want to buy the board Ramps 1.6 Plus. The description in the link says that is compatible with the driver TMC2130, but I found that there are two versions soldered in SPI mode. BIGTREETECH TMC2130 ...
1
vote
2answers
575 views

How to have double extruder and double Z motor on a 5-driver board?

We are using the Board SKR 1.3 with the following pins: ...
1
vote
2answers
513 views

Partial underextrusion in walls

I'm facing weird "pillars" of underextrusion on outer walls of my XYZ test cube. On the pictures below I`ve printed PLA test cubes with a 0.4 mm nozzle, 0.2 mm height and 210/50 °C ...
1
vote
1answer
1k views

Switch nozzle contact probe auto leveling with Marlin 2.0

I have a Robo R1+ which uses the nozzle contacting the glass print bed to level the printer. When the print head strikes the bed the Z-min endstops open signaling that the bed is touched. I recently ...
1
vote
1answer
172 views

Auto bed leveling offset issue

I'm using an Ender 3 with a new upgraded board SKR 1.3 Marlin bugfix 2.0 auto bed leveling I use EZABL. for the EZABL I followed their tutorial for Marlin 2.0 since I don't use the unified firmware. ...
0
votes
0answers
12 views

I am installing a BTT 24 v1.1 and it appears to be functioning in the 12864 mode with the exception of the top two lines which are gibberish

I am installing a TFT24 v1.1 and it appears to be functioning in the 12864 modes with the exception of the top two lines which are gibberish. I have attempted to block both the boot and the custom ...
0
votes
0answers
39 views

Hotend functioning inconsistently. PID completed normally, heating to quickly or not at all on print start up

I have a Xvico X1 printer which I had previously installed an SKR 1.3 on running Marlin, which was functioning normally. For Christmas I got a BLTouch, a heated bed and a Raspberry Pi for it, so I ...
0
votes
0answers
1k views

Error:Printer halted. kill() called! SKR 1.3 TFT35 3.0

I am trying to fix the very last error on my printer (custom built). Error:Printer halted. kill() called! This error occures about 5-10 minutes into a print (XYZ ...
0
votes
0answers
168 views

Printer froze mid print, stepper motor driver and MCU extremely hot afterwards. MCU seems dead now (?)

A strange problem occured while 3D printing. I've been printing for a long time now, and I consider myself fairly expeienced. normally, with every problem I've encountered with my printers (Anet, ...
0
votes
0answers
51 views

LV8729 on kossel issues with print dimensions (steps)

I've installed the an LV8729 on a kossel, configured with SKR 1.3 and marlin 2.0 with all the jumpers configured in the same way for 16 micro steps for X Y Z axis. Everthing seems fine the printer ...