Questions tagged [slic3r]

Questions related to the software slicing engine called Slic3r

Filter by
Sorted by
Tagged with
0
votes
1answer
95 views

Z-offset issues with Slic3r and Da Vinci Nano

I was attempting to use Slic3r 1.3.0 to print to my Da Vinci Nano, using MiniMover (a replacement for xyzprint) to load the G-code. The print seemed to be a couple of millimeters off of the bed, but ...
7
votes
3answers
21k views

Ender 3 severe under-extrusion

I've been using my Ender 3 for about four months now and it's been working wonderfully. The print quality is amazing and all the prints are very strong. Then about three weeks ago, my entire system ...
4
votes
1answer
215 views

My 3D printer checks axes home during print, often wrecking the print

My Tevo Tornado has picked up this habit along the way of checking axes during a print. (I say picked up because it didn't exhibit any problems when I got it. As far as I can tell the problem ...
1
vote
2answers
286 views

Pretty ugly surface remains after using support ramp. Are my slicer settings correct?

I'm printing a object with a pretty sizable overhang. And the results, after support removal, are pretty ugly. Here is the print before support removal. And here is the final product, sigh. Finally ...
3
votes
1answer
560 views

Prusa slicer and support material

I usually use Slic3r 1.3 but now I'm trying the new PrusaSlicer 2.2 that offers new features. I see that PrusaSlicer creates a ...
5
votes
3answers
8k views

How to change E0 to E1 on Marlin 1.1?

I have the same problem as this person but I don't have those lines in my RAMPS.h file as seen here. I've recently burnt my potentiometer on E0 so the motor isn't ...
8
votes
1answer
1k views

Skipping Y-steps, only when using Ultimaker Cura

In order to find out why my printer sometimes skips Y-steps (always in the same direction) only in Ultimaker Cura, I am digging into the G-code to understand the problem better. However, thousands of ...
2
votes
1answer
494 views

How to setup PrusaSlicer to support long bridges

Don't support bridge is a good idea to reduce support with acceptable print quality. But in this case, if I have a very long bridge and a short bridge, how do I tell the slicer to generate support ...
2
votes
2answers
631 views

Add brim everywhere, not just around the outermost line

I have a repair part that I need to print with ABS and I know that I have warping problems with ABS. I'm now trying to mitigate this by printing a circle around my object and use more brim. You can ...
5
votes
3answers
3k views

First layer - not even infill

I'm using Repetier and Slic3r and it is printing a gap between the perimeter and infill on the first layer. Also, the infill is lifting (as in photo). Any advise?
2
votes
1answer
64 views

Wrong calculation of E-parameter values

Hello dear Community, I am trying to print my first Box and I have a problem with the skin of the bottom layers. After finishing the slicing and while looking into the generated G-code I was wondering ...
1
vote
1answer
344 views

Is there a well-tested Ender 3 printer profile for PrusaSlicer available for download?

I am very comfortable with using PrusaSlicer and having a hard time adapting Cura. Is there any downloadable well-tested PrusaSlicer profile for some of the Creality printers?
1
vote
2answers
39 views

Can carving templates be produced from G-code?

I am looking for a way to generate 2D horizontal templates for manually carving an object. My thought was to produce an STL of the model, generate the G-code, and then transform that into slices. ...
5
votes
1answer
227 views

Why are there so many print speed parameters in slicers?

The expert mode of Slic3r PE has almost a dozen speed values: I understand that ultimately print speed at a particular temperature correlates with bond strength, so things like bridges and the first ...
1
vote
3answers
347 views

Useless head movements in PrusaSlicer

I love PrusaSlicer but I am having a problem. As you can see in the picture the head makes movements that seem useless (blue lines that come out of the print in the corners and go back instantly in ...
12
votes
1answer
2k views

Slic3r - Can I add new infill patterns?

Slic3r comes with a handful of infill patterns/algorithms, including Rectilinear, Hexagon, 3D Hexagon, Concentric, and Hilbert Curve. Are there any patterns/algorithms already made and available that ...
8
votes
4answers
3k views

Trouble printing small thin pole

3D-printing newbie here. I have a Geeetech's Prusa i3 mk2 B. I'm trying to print this: https://www.thingiverse.com/thing:1358311 That's a mold, with 2 external parts and a core. The exterior prints ...
0
votes
3answers
188 views

Under extrusion

I have a Prusa i3 3D printer and am using Slic3r for slicing. I've noticed that my extruder is underextruding. I've correctly set the nozzle diameter and the filament diameter and I've already tried ...
0
votes
1answer
33 views

Eliminating unwanted internal surfaces

One of the biggest challenges with 3D-drawings is internal surfaces unintentionally formed that cause slicing not to work properly. This is using SketchUp Pro, slicing with Slic3r, and printing with a ...
0
votes
0answers
202 views

Can't manage to force my print to standby while I insert a nut - Prusa Slicer and Tronxy XY2 pro

I use the Prusa Slicer on a Tronxy XY-2 pro which I believe uses RepRap firmware. I believe it uses RepRap firmware because I had to input it into the Prusa Slicer initialization questions, but I'm ...
0
votes
1answer
160 views

Sliced object losing all detail in Cura

I'm pretty new to 3D printing. I am using Repetier Host 2.6 with Slic3r (printer Geeetech i3 Pro B). When I slice detailed models I get issues like this as the slice result: This is the model in the ...
2
votes
2answers
297 views

Why are my lowest layers not solid?

I have designed this in Blender: The bottom is a regular n-gon with 0.8mm in height. In Slic3r, I see that the bottom-most layer is not solid: The green parts (of the first image) are going into ...
4
votes
1answer
906 views

How can I see what errors Slic3r have repaird?

I have an STL-file that Slic3r thinks has errors. They are not visible in the 3D view. I have had them anazlyzed in both Blender and netfabb. Both of these programs say that the model is good. I don't ...
1
vote
0answers
410 views

Prusa i3 Linux Mint Slic3r install problem

New to this domain, I got my prusa i3 last week and finished assemblage. Repetier params in Linux Mint 18 are ok too. I'm now trying to launch slic3r for the first time but I got this error launching ...
6
votes
3answers
4k views

Messy top layer with PETG filament?

I'm having issues getting PETG to print nicely. I have encountered pretty much every issue because when I fix one thing another issue pops up. I see people saying that you should "just copy your ...
13
votes
4answers
7k views

Why do some models appear broken in slicing software?

In my slicing software (Slic3r) some of the vertices/walls of my model seem to have disappeared, so that the inside of the model - which should be solid - is visible, while the surface appears as a ...
6
votes
2answers
787 views

Where to get the Slic3r configuration files for the 3D PrinterWorks Creatorbot printers?

I have a Creatorbot 3D printer made by 3D PrinterWorks. Their website appears to be down, as well as their Facebook page. To me it appears they are no longer around. I've installed Slic3r as 3D ...
2
votes
1answer
291 views

Inconsistent printing results using same settings but different calibration models

I've got a second-hand Renkforce RF1000 which I've gone into more detail about in this question. The extruder works however, I get some inconsistent results. First I printed a calibration cube and ...
2
votes
1answer
502 views

Temp Tower Setup Troubles -- Slic3r (How do you format G-Code {if} statements?)

I watched with great interest this video: Temp Tower - Slic3r Gcode Placeholders - How To - Chris's Basement -- Jan 23, 2019 Chris Riley I found a model I'm happy with: Smart compact temperature ...
1
vote
0answers
37 views

ETA for print job showing negative in Repetier host

I'm using Repetier host 1.0.6, and ever since adding default retraction settings, the "ETA" showing during a print job is negative: It stays this way throughout the print job, which is no fun, since ...
1
vote
1answer
34 views

Less filament from the half to the end

since some prints my printer (Geeetech i3) prints less and less filament over time: Notice, that the beginning is printed well: My settings for this print (Slic3r): ...
0
votes
0answers
417 views

Why on the Ender 3 does the hot end move too far on the Y axis after resuming print due to filament change?

When printing a model I pause the print at around 80 % complete to insert a new spool of filament since I'm at the end of my last spool of Polymaker PETG. I used Slic3r Prusa edition to slice the ...
4
votes
1answer
362 views

Change Slic3r settings for left handed coordinate system

I made my printer to have a left handed coordinate system (it homes to the back left corner of the heatbed), I did this because it happens to make working on the printer easier for me. This, however, ...
3
votes
2answers
4k views

What is M73 Q17 S43 G-code command?

I know that M73 P19 means "Set completion progress to 19%", and I suspect that M73 R42 means "Set remaining time to 42 minutes", ...
0
votes
0answers
60 views

Ender 3 with slic3r causes the head to go off the bed

I just downloaded slic3r and setup my settings on it, but when I sliced and started the print, the head went off the bed and then tried to print. It doesn't matter what I set the origin to, it still ...
6
votes
4answers
2k views

What determines print start location on the build plate?

I'm working with an older MakerBot Replicator clone, actually a Flashforge Creator 1, with original Creator firmware. I'm able to design objects, using Solidworks, and exporting the file as xxx.stl (...
5
votes
1answer
229 views

Print not centered

I have a Colido 2.0 printer that I cannot seem to get a print centered on the plate. I am using Slic3r and OctoPrint. If I use Repetier Host directly connected, I can get it to print correctly. I'm ...
2
votes
2answers
405 views

Weird surface thing

I have a 3D printer at home, the Colido Compact, and for some reason when I 3D print big flat surfaces a really weird thing happens. I'm using some PLA from Colido too I think It almost seems as if ...
5
votes
1answer
2k views

Starting G-code for auto Z probe offset

So, I like to take off my glass build plate from my printer bed because I don't like to put any force on the bed bearings but this presents an issue. I have an inductive bed leveling probe and each ...
3
votes
4answers
3k views

How do I get circles on small interior holes to adhere to the bed?

I’m using a RepRap printer, PLA (Hatchbox 1.75 mm), SketchUp, and Slic3r. The heated bed is covered with a blue polyester sticker. When I print small holes (1 to 1.5 mm radius), slicer software ...
3
votes
1answer
83 views

How to get rid of deforming small prints?

When printing a big base on the bed, I got no warping, but once I print small part (3 or less inches wide), there is a bit of warping on my piece as I remove it. It is 2 inches wide by 1 mm ...
5
votes
2answers
3k views

Sunken and rough bottom layer

Most of my part is printing very well, but I have problems in the bottom layer and in layers that are the first layers, but not necessarily layer 0. Looking at the print quality troubleshooting, I ...
2
votes
2answers
247 views

Speed issue with Slic3r and Marlin

I am trying to print with clay. These are my Slic3r speed settings, Other information; Nozzle: 1.4 mm First layer height: 0.9 mm layer height: 1 mm Filament dia: 1.8 mm perimeter: 3 When I print, ...
2
votes
1answer
702 views

Prusa i3, MK3: Firmware updated to 3.8.0. Display shows white blocks

About the printer: Prusa I3 MK3 [Sintron] Arduino Mega 2560 (just replaced) Replaced LCD / Smart controller FIRMWARE 3.8.0 Steps I have already tried: Replaced faulty Arduino Failed to flash ...
6
votes
1answer
579 views

Second layer of ASA print 'runs'

I am using a Prusa i3 MK2 to do a print in ASA, and I'm having a problem where on the second layer the plastic 'runs' into lines across the direction the head travels. It looks like the plastic is ...
4
votes
1answer
1k views

How is E value calculated in Slic3r?

I want to know the math behind how Slic3r calculates E values. $E_{value}$ represents amount of filament in mm (unless volumetric extrusion is selected) that has to be fed into the hotend to obtain a ...
2
votes
1answer
46 views

Minimum material deposit threshold in slic3r

I've been using Slic3r for a while now, and for the most part am happy with the results it produces. I mostly use the standard profiles provided by Prusa for my i3 mk3. However, when watching the 3D ...
1
vote
1answer
69 views

PLA infill/perimeter-layer to mimic real bone hardness

I friend of mine is in need to have human bone printed for educational purpose. Of what I understood they will use it for practicing drilling in it and thus need the printed bone to mimic a real bone. ...
3
votes
0answers
29 views

Selective reinforcement of some places in my part [duplicate]

I have a part that experiences larger than average forces in some of its protrusions. It would make sense to reinforce walls, and in particular strengthen infill in those areas. But to save material ...
8
votes
2answers
681 views

What is wrong with my "disable sensor" gcode?

I have a spool of translucent PLA filament that doesn't work well with the filament sensor on my Prusa i3 MK3. The translucency trips up the sensor, making it think the filament ran out. I thought I'd ...