Questions tagged [th3d]
The th3d tag has no usage guidance.
15
questions
0
votes
0
answers
76
views
Z-offset making no difference
I have an Ender 3 V2. I flashed it to TH3D Unified Firmware 2.62 and installed a BLTouch. It appears to be working, if I auto-home it, the probe is activated and the print head retracts. Problem is ...
0
votes
1
answer
637
views
Ender 5 Pro w/4.2.2 & BLTouch does not apply previously saved Z-offset
Installed a BLTouch on an Ender 5 Pro. As usual, the official firmware from Creality is buggy trash (wrong BLTouch offsets, only 9 point probing, etc.) and useless to me.
I compiled and flashed the ...
- 81
0
votes
0
answers
220
views
E1 printer halted error
I changed the hot end from the stock Creality CR-10 v2 to an e3D v6. Since it uses a type 5 thermistor, I had to change the firmware; after a quick search I found the TH3D firmware which I used, I did ...
- 1
1
vote
1
answer
363
views
Ender 3 not allowing z=0 regardless of z offset value
Using TH3D firmware with some small changes to allow manual mesh levelling and to increase the serial baud rate, neither of which are active when the error presented.
When auto home is used either ...
2
votes
1
answer
447
views
Program Creality v2.2 board to use HEATER1 transistor for HEATER0
My CR10-S5 with Creality v2.2 mainboard recently suffered from the hotend heater transistor (MOSFET) failing short. After taking a look at the board, I tried to be clever and use the ...
- 61
1
vote
1
answer
847
views
First half of the prints are getting stretched on the Z axis
I have an Ender 3 Pro with a BLTouch 3.1 attached and I have this weird problem. Whatever I print, whether it's a 3rd party STL ...
- 131
4
votes
2
answers
2k
views
Creality Ender 3 Pro - Z travel issue with TH3D firmware
TLDR - I’ve just driven myself insane trying to fix what I thought was a physical problem with my Z-axis, but it seems to have been solved by switching from the TH3D firmware to the Creality firmware. ...
- 143
1
vote
1
answer
2k
views
Re-doing manual bed leveling
I have a Ender 5 Pro with a BLTouch auto bed leveler, running TH3D's version of Marlin: TH3D UFW 2.14. During my initial setup several months ago, I naively assumed that the BLTouch didn't need a ...
- 111
1
vote
0
answers
1k
views
How can I get my printer to home correctly?
I have a Creality CR-10 with EZABL (bed leveling sensor). I'm not sure what prompted the printer to think the center is the origin.
The printer homes in the dead center of the bed to start the auto ...
- 131
2
votes
3
answers
3k
views
Z offset not working after flashing TH3D firmware
I had the BLTouch (3.1) working with stock firmware on an Ender 3 v2 but wanted to get a 5x5 mesh instead of the 3x3 so I installed the TH3D firmware. With the stock firmware my Z-offset was -2.95 mm.
...
- 179
0
votes
0
answers
714
views
CoreXY printer homes in the wrong direction, but moves correctly when moved manually
So I'm using TH3D firmware on my CoreXY printer and when I move it from the LCD it moves correctly, but when I try to home X or Y it goes in the wrong direction. It's set to home to min in firmware. ...
1
vote
1
answer
992
views
Cannot configure default E step for extruder on TH3D
I installed the TH3D firmware to my Ender 3 Pro yesterday and today I am trying to configure the extruder rate because I am not using the stock extruder on my printer but have swapped in a BMG ...
- 25
1
vote
1
answer
1k
views
BLTouch with TH3D Ender 3 pro
I installed TH3D to my stock mainboard via this guide, but BLTouch does not work properly.
It does not check all 9 points before point it just go middle then check z then start printing. BLTouch ...
- 25
1
vote
0
answers
1k
views
E-steps somehow reset, how could it have happened
Background
After installing a direct drive extruder (E3D Hemera) to my CR-10S, I calibrated the E-steps so that adequate extrusion would happen; going from ~95 steps/mm to ~390 steps/mm.
...
- 839
4
votes
5
answers
25k
views
How Do I Speed up The BLTouch Auto Bed Leveling In TH3D's Unified Firmware?
I have just upgraded my board to TH3D's EZBoard Lite with their Unified Firmware (U2.R1.15) and whilst dialling in all the setting I have found that using the BlTouch each time to be frustrating ...
- 679