Questions tagged [z-axis]

Use this tag for questions related to specific movement of the Z direction of the printer - Questions about a machine or 3D model's Z-axis

17 questions with no upvoted or accepted answers
Filter by
Sorted by
Tagged with
2
votes
1answer
57 views

Problems with the right Z axis

My 3D printer was working perfectly, but one day I put it inside an acrylic box and put it to work, that was not a good idea, because the Z axis grabbed the box, after that, the Z axis started to ...
2
votes
0answers
42 views

Z Offset Keeps Changing Flashforge Hunter

I am a newbie and I started having printing problems with my Flashforge Hunter. I found out that with every calibration the building plate Z offset is getting larger by approx 0.1 mm to 0.2 ...
2
votes
0answers
57 views

Z Axis homes, then bounces up 15 mm and stays there when printing

Prusa, I3 Mk2. Marlin 2.0.3 The test model printed fine prior to installing Marlin 2.0.3. It's not the slicer or GCode. I tried several models, and all of them worked perfectly prior to the update. ...
2
votes
0answers
532 views

Does matching whole Z-motor steps for layer height actually matter on Ender 3?

This question asks about computing the fundamental layer height unit for full Z-motor steps, on the basis of a theory that layer thickness can be inconsistent if the height is at different micro-...
2
votes
0answers
636 views

Inconsistent Auto Bed Leveling - Having To Calculate Z Offset For EVERY Print

I am having a problem with my Flying Bear P902 3D printer where I have to calculate the Z offset for every single print. I calculate it using this method (and store it in EEPROM) : Link to ...
2
votes
1answer
344 views

Wrong Z-Axis movement in G-Code

Alright so I bought a broken UP mini. There was only a defect on the board so I connected the components to a Duet 2 Wifi. Everything is fully operational and I can manually move all axes correctly ...
1
vote
0answers
233 views

What can cause Z height loss in the first few layers?

All my prints come out about 1 mm too short in the Z dimension. So for example a 20 mm cube comes out 19 mm high. A 10 mm cube comes out 9 mm high. The X and Y dimensions are fine. There's a little ...
1
vote
0answers
91 views

Monoprice MP10 Mini, can't get a decent print

Update: if i press the button "Home" it will correctly posizionate the nozzle above the printing bed, with a gap wide enough to insert a sheet of paper between the nozzle and the surface. But, and ...
1
vote
2answers
953 views

Ender 3 home location

I have an Ender 3 and I have a problem with auto home. I use auto home and then level the bed with the wheels beneath the bed. I then start a print and the first layer is well above the bed. Perhaps ...
1
vote
0answers
31 views

Large SLA Build Plate

So I purchased a ready-made z-axis. There are four holes for 6 mm screws. Two pairs of holes are 100 mm apart, with each pair of screw mounts 20 mm apart from each other. Basically, ...
0
votes
0answers
18 views

Ender 3 nozzle moves through previous layer on lithophane

I'm trying to print lithophanes and having an issue with the nozzle moving through the previous layer and basically "drawing" through the print. I've printed 3 lithophanes before with zero ...
0
votes
1answer
66 views

BLTouch Z offset needs changes

Just installed a BLTouch sensor on my Ender 3 Pro (using firmware version: Ender-3 Pro1.1.6BLTouchV3.1PowerLossContinueEnglish), it all works great but each time I ...
0
votes
1answer
32 views

Print quality: possible Z wobble

The printer I am using is an Artillery Sidewinder X1. In the photos attached you can see that I am having a lot of inconsistency between layers. The problem has never gone away and I always thought it ...
0
votes
1answer
116 views

Waves in my prints

Around about 2 weeks ago I upgraded my Ender 3 Pro with a micro Swiss direct drive and all metal hotend. I had some tuning with the PID and e-steps to do, but once that was done, it's been mostly good....
0
votes
1answer
60 views

Z-offset issues with Slic3r and Da Vinci Nano

I was attempting to use Slic3r 1.3.0 to print to my Da Vinci Nano, using MiniMover (a replacement for xyzprint) to load the G-code. The print seemed to be a couple of millimeters off of the bed, but ...
0
votes
0answers
262 views

Very unusual diagonal banding

Edit #2 Title changed again to better reflect the nature of the issue. I installed the Z axis motor at the top of the frame to help alleviate any misalignment that may be occurring. The Z axis runs ...
0
votes
0answers
43 views

Anet A8 moves down into piece, destroying it, just before the printer is set to finish

I hope someone can help me figure out what's going on with my printer. I have been printing a couple of pieces and it's been printing perfectly. But for some reason every now and then, the printer ...