Skip to main content
8 votes
Accepted

How do I know when filament is getting old, and what things can I do to correct for it?

The primary issue with long-term exposure of filament to the environment is that it will absorb water moisture from the air. When a filament that has absorbed water is passing though the hot end of a ...
mbmcavoy's user avatar
  • 798
8 votes

Any fix for PLA prints getting more brittle over time?

PLA absorbs moisture, so keeping the filament dry is a key factor. Aside from that, PLA is naturally more brittle than other plastics like ABS and Nylon Sorry, tried to find a graph to prove it, but ...
tbm0115's user avatar
  • 6,324
6 votes
Accepted

Any fix for PLA prints getting more brittle over time?

Increase nozzle temperature. When the filament is new it will print easier, requiring less heat to print well. So if you didn't store your filament properly to begin with, increasing print temperature ...
Tormod Haugene's user avatar
5 votes
Accepted

How important is the dimensional accuracy of filament relative to the detail of a print?

Dimensional accuracy is not as important as dimensional uniformity. I can print with undersized (or oversized) filament, adjusting the flow appropriately, provided the filament has a consistent ...
Davo's user avatar
  • 2,440
5 votes
Accepted

Stone-look surface via painting?

It's totally possible to achieve but the result vastly depends on your painting skills and your spray paint quality. Your can look at this page for a concrete example. How it compares to stone ...
exb2800's user avatar
  • 66
5 votes

What is causing 'droplets' on first layer?

Mine is more of an educated guess than a definitive diagnosis, but it looks to me like if your printer may be overextruding (it's difficult to say with certainty with this particular picture, but your ...
mac's user avatar
  • 4,725
4 votes

Filament long term storage

In theory, most filaments don't go bad within a year. However, praxis shows, that averse conditions can impact the filaments over time and age them to unusability. Among the damaging factors is heat, ...
Trish's user avatar
  • 22.2k
4 votes

Why does my PLA filament keep snapping?

PLA seems to become brittle with age. Micro-fractures develop on the surface, and they will grow if filament is taken off the spool and held straight. This behaviour does not seem to be linked to ...
Mick's user avatar
  • 3,180
4 votes

How do I know when filament is getting old, and what things can I do to correct for it?

Moisture creeps into the filament when PLA is exposed for a long time to a humid environment. This is audible like popping bubbles when heated in the hotend and does worsen the print quality. The ...
0scar's user avatar
  • 36.2k
4 votes

Humidity sensor says drybox isn't that dry - are my expectations unrealistic or is something wrong?

Track humidity graph over days (one measurement every 3 hours is fine). Be careful that polling the sensor too often may warm it up and cause inaccuracies, the temperature dependence is quite strong. ...
FarO's user avatar
  • 4,373
3 votes

Why does my PLA filament keep snapping?

When water gets absorbed into the filament, it causes some of the long chain polymers to break. This is a permanent reaction that cannot be fixed by baking the filament, which typically results in the ...
user77232's user avatar
  • 2,448
3 votes

Are black filaments more brittle?

Not inherently. There are two things at work that might cause one color to test weaker than others even as its properties otherwise are functionally identical: A bad print among good ones. A bad roll ...
Trish's user avatar
  • 22.2k
3 votes

Mystery filament cleaning fluid

That's a filament cleaner/oiler combo. The black bottle is a variety of machine oil. The effect of oilers on prints is heavily disputed in the community. The suggestion of plant oils is a very bad ...
Trish's user avatar
  • 22.2k
3 votes
Accepted

What is causing 'droplets' on first layer?

First of all, thanks for all the help, it really is a nice community! But none of them actually helped and I finally find out what to actually do to fix the problem so here it goes: Extruder ...
Valmond's user avatar
  • 914
3 votes

How important is the dimensional accuracy of filament relative to the detail of a print?

Put it simply: they say 1.75 mm with a ± error of 0.05 mm. Which means your flow may vary ±2.9 % while you are printing creating blobs and such. The smaller the ...
osirisstar's user avatar
3 votes

What is "HDPLA", and why is it so hard to find out more about it?

So, low-teck, old-style investigative work from my side.... I contacted a company selling HDPLA and they got back to me with the following reply. We created HDPLA as an industrial PLA with special ...
mac's user avatar
  • 4,725
2 votes

MakerFlex Spool has bubbles?

Bubbles are a defect. Two problems can occur: The air in the bubble will be under pressure when heated and can cause a little blow-out when the plastic sides of the bubble are soft enough that they ...
cmm's user avatar
  • 4,551
2 votes
Accepted

What type of plastic can be used to produce your own filament?

Filament manufacturers (for example, Colorfabb) also sell pellets, price per kilo would be about 10 times less than the same plastic in filament form. Out of household garbage only ABS can be easily ...
Oleg Mazurov's user avatar
2 votes

Are black filaments more brittle?

Your heading is about how brittle the material is, but the question is asking about layer adhesion. I'll go ahead and tackle the layer adhesion portion. There are many variables at play here but ...
Anthony Herrera's user avatar
2 votes

Creality CR-10 extruder clicking and/or nozzle clogging

Turns out the filament was the problem, I tried printing a model with a high quality sample PLA filament I had and it printed perfectly; one of the cleanest prints I've had. Never skimp on filament.
CouscousKingpin's user avatar
2 votes

Which is the right filiament type to print breakable children's toy parts such as small gears

I won't even ask why you need this and I assume you've done your homework about the issues. 3D printed gears are notorious for failing even when designed well, so the idea in general should be pretty ...
Anthony Herrera's user avatar
2 votes

Which is the right filiament type to print breakable children's toy parts such as small gears

deliberate/planned obsolescence is the term you look for If you design parts that break after some time, you plan their obsolescence. That you do by a deliberate choice of material and working ...
Trish's user avatar
  • 22.2k
2 votes

Humidity sensor says drybox isn't that dry - are my expectations unrealistic or is something wrong?

Alright, there were some good suggestion in the comments, and I gave them a look, but I think I solved this myself. I think, after a lot more testing, that it was some combination of stratification ...
DodoDude700's user avatar
2 votes

Looking for 3D filament thats compatiable with HHO-oxyhydrogen and NaOH sodium hydroxide -lye

Polypropylene should be good, and relatively easy to print. Prinsco rate its resistance to NaOH as A-Excellent. Ultimaker provide a useful guide to the chemical resistance properties of 3D printing ...
Mick's user avatar
  • 3,180
2 votes
Accepted

My Hatchbox PLA filament only allows me to use rafts

PLA is a forgiving filament, you can even print such filament without a heated bed. Although there are differences in quality between brands, PLA shouldn't need a raft to be printed. Hatchbox filament ...
0scar's user avatar
  • 36.2k
2 votes

My Hatchbox PLA filament only allows me to use rafts

It is unlikely this is a filament material issue since many of us have used Hatchbox PLA without this issue. This is a first layer adhesion issue. Your bed may not be clean, or the bed may have had ...
Perry Webb's user avatar
  • 2,376
1 vote

Why does my PLA filament keep snapping?

PLA snapping is pretty universal. The best countermeasure is to always remove the filament from the printer after a print and place it in a low-humidity chamber. Other answers speak of moisture-...
cmm's user avatar
  • 4,551
1 vote
Accepted

Are black filaments more brittle?

I have some experience in the textile industry and it is known that items, whether piece goods or yarn, which are black (for most fibers) it is likely an over-dye; colors that failed to match the ...
Jim Kennedy's user avatar
1 vote

Filament long term storage

I expected more than a couple months but perhaps I am wrong? It depends on the filament, the shipping and the local conditions. I'm on an Island, so very high humidity. We have several useless spools ...
Kilisi's user avatar
  • 1,385
1 vote

Filament long term storage

The answer is that it depends on the climate you are in or the climate in your house. The more humid, and the higher the temperature, the faster the moisture is taken up in the filament (note also ...
0scar's user avatar
  • 36.2k

Only top scored, non community-wiki answers of a minimum length are eligible