Stepper motors contain two distinct sets of coils. The current in these coils is governed by your stepper motor driver.
To move the motor in either direction, the coils are being driven one after another, and in different directions.
Imagine this being a normal 3-phase AC motor, but instead of three phases, only two are used.
A "full steps" (1/1 "...
I want to add some points and clarifications to the answer that @darthpixel already has given. Most information you need is in there, I want to give some more practical advice, since that is what I understand you're question is asking for. I'll start with some points on the more theoretical side, though:
notice that the Vref is not a voltage that is passed ...
Generally speaking voltage on stepstick output should be around 1V.
To imagine more or less what the current and what the voltage is, you can think about it in the same way as about water.
The wire is more or less the same as the pipe.
The voltage can be imagined as (sort of) the height from which the water flows but the current can be imagined as an ...
Did you heat the hotend before attempting to move the extruder? Most firmwares block cold extrusion. If you send the printer M302 it will allow the extruder motor to move without the hotend being above the temperature set in the firmware. Jumpers next to drivers are used to set microstepping, no need to adjust these unless you changed to a different type ...
In the configuration.h file of Marlin 2.0.x you can define which stepper driver type is used to drive the stepper in the Stepper Drivers section.
You can choose to use the following constants from the array to configure the correct driver:
['A4988', 'A5984', 'DRV8825', 'LV8729', 'L6470', 'TB6560', 'TB6600', 'TMC2100', 'TMC2130', 'TMC2130_STANDALONE', '...
To Protect, or Not to Protect
From the web site you reference:
The SilentStepStick Protector is an add-on module for StepStick and
Pololu A4988 compatible stepper motor drivers. The board provides
flyback diodes (freewheeling diodes) for the motor outputs, so that
they are also protected against induction voltages in the unpowered
state of the ...
Many of the motors that look like stepper motors in laser printers are actually three-phase brush-less DC motors. These look like stepper motors, but are intended to be used differently, controlled differently, and serve a different function. Like stepper motors, they have a permanent magnet rotor surrounded by coils of wire.
They typically are used in ...
Yes you can mix different drivers, including the TMC drivers (e.g. using for X and Y only).
How you do that is described in this instructable.
Please do note that, from observations, the 8-bit based Arduino boards and shields such as the RAMPS are becoming more or less obsolete; the 32-bit based controller boards are becoming mainstream. Such boards have a ...
Usually if they get too hot you have to adjust the amperage by turning the little potentiometer on the A4988 (turn left until you can move the motor by hand, turn right until you cant, add a little bit like 1/8 to 1/4 of a turn).
I used a different stepstick RAMPS card and Mega, they worked perfectly.
it is not completely clear, so:
the A4988 ...
Obviously, your extrusion process is troubled by a lot of pressure. This can be seen from the extensive experiment you conducted with PLA extrusion at different temperatures. Please do note that 230 °C is considered pretty high for PLA! Usually it should be in the range of 185 - 205 °C:
In general, PLA filament settings have an optimal printing ...
Closed loop steppers like S42B are becoming popular for the spatial axes because compensating for skipped steps is the correct way to recover for those axes. For example, if the nozzle knocks into a warped corner of a print and skips, the right thing to do is compensate, commanding additional steps necessary to get to the commanded location.
This is less ...
Yes, they are shipping the v2 with the 4.2.2 board. My understanding is that the 4.2.7 board has a change in the stepper driver pinout but is otherwise the same as 4.2.2. The change in the pinout allowed them to change the stepper driver package as the stepper driver vendor appears to be changing that spec. I've used both boards in my V2 with no ...
I notice that in "configuration_adv.h" for the BIGTREETECH-SKR-mini-E3, which uses TMC2209 drivers, the similar section has:
#define HOLD_MULTIPLIER 0.5 // Scales down the holding current from run current
#define INTERPOLATE true // Interpolate X/Y/Z_MICROSTEPS to 256
As far as I can see on the attached videos your homing movement is reversed.
as per Marlin, the homing for X shall move towards the left side and for Y to the back of the printer.
That could occur when: cable connectors to stepper motors are reversed, or the motor is assembled the other way (you can set reverse direction in Marlin)
The other issue is steps/...
So I feel that I solved the problem thanks to a few sources. Thanks to 0scar for his quick response and help.
The problem was two fold. Mechanical problem causing blockage and slicer setting causing ripple.
The PTFE tube wasn't pushed all the way in as far as it could go causing too much pressure in the hotend. This seems to be a really common problem with ...
I have fixed it. I tried uploading the bugfix version of Marlin and no luck. Then I noticed a loose jumper wire that connected the driver to the board and when re-installing it I noticed it didn't grip the pin that strongly and could be easily pulled off so I switched the wire and everything works now. Turns out that even jumper wires can have a bad ...
If an extra few degrees of heating the hot end does not work, you could try to increase the amount of Ampere through the steppers. Increasing the current will increase the torque of the stepper.
The question is what your current Vref of your extruder stepper driver is. To get a maximum current of 1 Ampere you require a Vref of 0.4 V if you have genuine ...
Even though you may have acceptable extrusion, any clicking from that area of your printer is likely to be a missed step on the extruder motor. This may be insignificant with respect to print quality, but as you suggest, it is an irritation.
If you are confident that your nozzle is clean of debris (which is likely), you could consider to raise the nozzle ...
Let's see what we have:
The fuse in the driver is set to keep up the loads that the driver can safely handle.
The NEMA 17 results in a blown out fuse
The problem lies not in the driver, but the NEMA 17 motor or the wires to it and can be of several ways:
The motor has a short and is defective.
The motor is not rated to the driver ...
If the fuse blows - there is a reason for that, so changing it for a higher rating without understanding the source of the problem is:
Asking for fire!!!
Every stepper has its own internal resistance (and as we have a magnetic field it is called a reluctance), that is limiting the max current, but this equation needs to take U given to the motor.
If the motors are in parallel, then setting it at 0.4V means each motor will only get a quarter of the current a single motor would get at 0.8V. If you set it to 0.8V each motor will get half. I think 0.8V (same as for the other motors) would be an appropriate setting. Stepper drivers are constant-current, not constant-voltage.
Are the steps/mm for your Z-...
I'm not sure I know exactly what is wrong or what steps you've taken so far, but it seems like your extruder motor is broken and you've narrowed the problem down to electronics.
If so, replacing the Arduino, motor, and driver leaves only the Ultimaker PCB as the source of the problem. I would suggest ordering another - but not until you've contacted ...
You have to know:
distance between belt teeth (usually 2mm)
number of teeth on pulley
motor step angle 1.8 deg?
microstepping count, probably 16?
Then you can enter all these numbers info the calculator here:
That depends on how much noise you have on your motor power supply ground. You definitely want the 100 µF capacitor to have a good high frequency response. Motors turning on and off can be noisy, and that noise can cause false clock signals in your logic circuitry if you tie the grounds together.
(This is more of an electronics.stackexchange.com question btw).
It is not only ok, it is absolutely necessary. The systems won't operate correctly unless all the gnds are tied together. Since this is a stepper motor, you don't have to worry about noise getting back onto the power supply lines for the logic supply, since the stepper board has a decoupling ...
The driver has a potentiometer to change the voltage that is giving to the motors.
As one person answered me in another question, I would need 3.2 V to make the motor work well (2. Ω * 1.3 A = 3.2 V).
You are misunderstanding that answer and what the potentiometer does. The potentiometer does not control the voltage going to the motors. It makes no ...
There is no problem with using 4 motors instead of 5. The 5th slot is provided to enable use of a second extruders, but many people only have a single extruder printer and leave the 5th slot unused.
how will Marlin figure out which slot the extruder is connected
Which stepper motor is in which slot is something you can configure in the firmware. There is ...
To be more speficic: RAMPS board (versions 1.3 - 1.6) offer possibility to connect 5 stepper motor drivers (on the board marked X, Y, Z, E0, E1) and 6 stepper motors, because the Z axis motor's connector is doubled (this is classic design of reprap printer). I could also see other RAMPS versions/clones (1.6+, 1.7 prototype) which have ...
I solved this problem by change EEPROM value to "2" in Configuration.h:
#define EEPROM_MODE 2
Now ZAXIS_STEPS_PER_MM value load from firmware, not EEPROM.
#define EEPROM_MODE 0
— does not result in my case.