Return to Question

I'm using a Tronxy Ultrabot (looks very similar to Anycubic Photon) and I'm still on my first prints. Things that happened thus far: many failed prints that stuck to the resin tank, one which I had to carefully scoop off.

What I'm finding odd is that this sheet (for lack of a better term) only seems to happen on one half of the whole thing.

I'm suspecting the FEP film is the culprit here, due to earlier failures.

What else could be causing this error? Other info that might be important, the model is using 6 layer, 60s cure time for base; 0.04mm layer size, 10s layer cure time, 1s delay between layers. The resin is Suen Ching

I'm using a Tronxy Ultrabot (looks very similar to Anycubic Photon) and I'm still on my first prints. Things that happened thus far: many failed prints that stuck to the resin tank, one which I had to carefully scoop off.

What I'm finding odd is that this sheet (for lack of a better term) only seems to happen on one half of the whole thing.

I'm suspecting the FEP film is the culprit here, due to earlier failures.

What else could be causing this error? Other info that might be important, the model is using 6 layer, 60s cure time for base; 0.04mm layer size, 10s layer cure time, 1s delay between layers. The resin is Suen Ching

Edit 2: Here's the manual

I'm using a Tronxy Ultrabot (looks very similar to Anycubic Photon) and I'm still on my first prints. Things that happened thus far: many failed prints that stuck to the resin tank, one which I had to carefully scoop off.

What I'm finding odd is that this sheet (for lack of a better term) only seems to happen on one half of the whole thing.

I'm suspecting the FEP film is the culprit here, due to earlier failures.

What else could be causing this error? Other info that might be important, the model is using 6 layer, 60s cure time for base; 0.04mm layer size, 10s layer cure time. The resin is Suen Ching

I'm using a Tronxy Ultrabot (looks very similar to Anycubic Photon) and I'm still on my first prints. Things that happened thus far: many failed prints that stuck to the resin tank, one which I had to carefully scoop off.

What I'm finding odd is that this sheet (for lack of a better term) only seems to happen on one half of the whole thing.

I'm suspecting the FEP film is the culprit here, due to earlier failures.

What else could be causing this error? Other info that might be important, the model is using 6 layer, 60s cure time for base; 0.04mm layer size, 10s layer cure time, 1s delay between layers. The resin is Suen Ching

I'm using a Tronxy Ultrabot (looks very similar to Anycubic Photon) and I'm still on my first prints. Things that happened thus far: many failed prints that stuck to the resin tank, one which I had to carefully scoop off.

What I'm finding odd is that this sheet (for lack of a better term) only seems to happen on one half of the whole thing.

I'm suspecting the FEP film is the culprit here, due to earlier failures.

What else could be causing this error?

I'm using a Tronxy Ultrabot (looks very similar to Anycubic Photon) and I'm still on my first prints. Things that happened thus far: many failed prints that stuck to the resin tank, one which I had to carefully scoop off.

What I'm finding odd is that this sheet (for lack of a better term) only seems to happen on one half of the whole thing.

I'm suspecting the FEP film is the culprit here, due to earlier failures.

What else could be causing this error? Other info that might be important, the model is using 6 layer, 60s cure time for base; 0.04mm layer size, 10s layer cure time. The resin is Suen Ching