Skip to main content
3D Printing

Return to Question

added 662 characters in body
Source Link
Bobby McGlone
Bobby McGlone
  • 51
  • 1
  • 5

More details about my setup is: A Robocraze 3D Printer Controller Board RAMPS 1.4 using A4988 stepper motors drivers and my motors are the nema 17 stepper motors. I currently have the two z axis motors wired in parallel but have tried before using series, however the problem of being unable to control the direction of the Z motors still arises (can easily switch back to series).

currently trying with no load just to get the motors turn in the correct direction when I send a G-code command. I am using Repetier host on ubuntu 14.04.5.

I have also check the endstops and they are working perfectly, so they ain't a problem (I don't think :p)

More details about my setup is: A Robocraze 3D Printer Controller Board RAMPS 1.4 using A4988 stepper motors drivers and my motors are the nema 17 stepper motors. I currently have the two z axis motors wired in parallel but have tried before using series, however the problem of being unable to control the direction of the Z motors still arises (can easily switch back to series).

currently trying with no load just to get the motors turn in the correct direction when I send a G-code command. I am using Repetier host on ubuntu 14.04.5.

I have also check the endstops and they are working perfectly, so they ain't a problem (I don't think :p)

added 56 characters in body
Source Link
tjb1
tjb1
  • 2.1k
  • 16
  • 26

//// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {5060, 5060, 2*60, 0} // set the homing speeds (mm/min)

#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,590}
#define DEFAULT_MAX_FEEDRATE {300, 300, 3, 45} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {1000,1000,50,500} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for retracts

#define DEFAULT_XYJERK 10 // (mm/sec) #define DEFAULT_ZJERK 0.3 // (mm/sec) #define DEFAULT_EJERK 5.0 // (mm/sec)

//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {50*60, 50*60, 2*60, 0}  // set the homing speeds (mm/min)

#define DEFAULT_AXIS_STEPS_PER_UNIT   {80,80,4000,590}  
#define DEFAULT_MAX_FEEDRATE          {300, 300, 3, 45}    // (mm/sec)
#define DEFAULT_MAX_ACCELERATION      {1000,1000,50,500}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION          1000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION  1000   // X, Y, Z and E max acceleration in mm/s^2 for retracts

#define DEFAULT_XYJERK                10   // (mm/sec)
#define DEFAULT_ZJERK                 0.3     // (mm/sec)
#define DEFAULT_EJERK                 5.0    // (mm/sec)

//// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {5060, 5060, 2*60, 0} // set the homing speeds (mm/min)

#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,590}
#define DEFAULT_MAX_FEEDRATE {300, 300, 3, 45} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {1000,1000,50,500} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for retracts

#define DEFAULT_XYJERK 10 // (mm/sec) #define DEFAULT_ZJERK 0.3 // (mm/sec) #define DEFAULT_EJERK 5.0 // (mm/sec)

//// MOVEMENT SETTINGS
#define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E
#define HOMING_FEEDRATE {50*60, 50*60, 2*60, 0}  // set the homing speeds (mm/min)

#define DEFAULT_AXIS_STEPS_PER_UNIT   {80,80,4000,590}  
#define DEFAULT_MAX_FEEDRATE          {300, 300, 3, 45}    // (mm/sec)
#define DEFAULT_MAX_ACCELERATION      {1000,1000,50,500}    // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION          1000    // X, Y, Z and E max acceleration in mm/s^2 for printing moves
#define DEFAULT_RETRACT_ACCELERATION  1000   // X, Y, Z and E max acceleration in mm/s^2 for retracts

#define DEFAULT_XYJERK                10   // (mm/sec)
#define DEFAULT_ZJERK                 0.3     // (mm/sec)
#define DEFAULT_EJERK                 5.0    // (mm/sec)
Source Link
Bobby McGlone
Bobby McGlone
  • 51
  • 1
  • 5

Z axis Stepper motors not working correctly

I have been searching around the internet for the last 3 days trying to figure this out. My Z axis motors for a pursa-i3 3d printer are not working correctly. I have marlin firmware and using repetier host. I send a command to move the z axis and I get it to move, however I if I send the same command again the motors will sometimes spin the other way. feel like They almost randomly choose which direction they turn.

As I said I have been trouble shooting this for a while now. What I am suspecting is the firmware feedrates and acceleration or some setting is not correct.

Here is my code:

//// MOVEMENT SETTINGS #define NUM_AXIS 4 // The axis order in all axis related arrays is X, Y, Z, E #define HOMING_FEEDRATE {5060, 5060, 2*60, 0} // set the homing speeds (mm/min)

#define DEFAULT_AXIS_STEPS_PER_UNIT {80,80,4000,590}
#define DEFAULT_MAX_FEEDRATE {300, 300, 3, 45} // (mm/sec) #define DEFAULT_MAX_ACCELERATION {1000,1000,50,500} // X, Y, Z, E maximum start speed for accelerated moves. E default values are good for Skeinforge 40+, for older versions raise them a lot.

#define DEFAULT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for printing moves #define DEFAULT_RETRACT_ACCELERATION 1000 // X, Y, Z and E max acceleration in mm/s^2 for retracts

#define DEFAULT_XYJERK 10 // (mm/sec) #define DEFAULT_ZJERK 0.3 // (mm/sec) #define DEFAULT_EJERK 5.0 // (mm/sec)

I tried swapping the drivers around and the motors will work perfectly on another axis so I don't suspect it to be a driver issue. I have been turning the pots ontop of the drivers to make them work but can't make them to go the same direction i want them to.

I've checked the wires and I almost sure they are wired up correctly. (could be wrong but have checked it over with a multimeter.)

I am new to this and it's my first time building one of these would appreciate any help I can get and and maybe I have over looked something I have tested. Just really want the axis to move in the direction That I say it to move in.

Thank you, Bobby