Questions tagged [flashforge]
Questions using this tag should involve products of FlashForge Corporation
17 questions
0
votes
0
answers
17
views
FlashForge Adventurer 3 cooling fan making grinding sound while printing/cooling the nozzle
Ever since I got this printer for my 15th birthday the cooling fan has made a grinding sound when the printer starts to extrude during printing/nozzle cooling. How can I fix this?
1
vote
2
answers
395
views
Managing Flashforge Guider 3 Plus printer on Ultimaker Cura
I seem to be having trouble managing the printer for slicing process in Ultimaker Cura. I use Flashforge Guider 3 Plus printer and added it to Ultimaker Cura manually (there was no Guider 3 Plus ...
- 37.1k
1
vote
1
answer
788
views
Adventurer 3 Not loading Filament/Grinding Sound
Have had my second Adventurer 3 now about 3 weeks. Used all of the red filament that comes with it but when I go to load new FlashForge filament in the unit, I can't even get it to suck up the ...
0
votes
0
answers
27
views
FlashForge Creator Pro 3 - tlumping together
I am trying to do 48 4 mm wide cylinders at a time 5-25 mm apart and after the first few layers are put down they all get caught up together and the machine goes around collecting them all into 1 ...
- 37.1k
1
vote
0
answers
160
views
Adventure 3 ABS problems with raft and quality
So I started using ABS yesterday, I have done multiple prints and the quality was amazing to start with, but now I'm getting small protrusions out of the layers. I use the FlashPrint fine settings for ...
- 1,694
3
votes
2
answers
3k
views
Why does FlashPrint have different (non-100%) default extrusion ratios for different filaments?
In FlashPrint there is an Extrusion Ratio setting. It's set to 97 % for the stock PLA profile and 107 % for the stock PETG profile.
I would've thought these would be 100 % by default (and the same for ...
2
votes
1
answer
2k
views
What does the "Control Module" setting in FlashPrint 5.1 do?
I don't understand the description of this setting in FlashPrint and have been unable to find a better description online. What does it do?
- 275
2
votes
1
answer
319
views
Flashforge Adventurer 3 Spool mounting
I have just purchased the above 3D printer and the mount for the spool does not fit the new spool. The external spigots are too large and there is no axle shaft that would have helped.
This is a photo ...
- 6,688
1
vote
2
answers
3k
views
Adventurer 3 3D Printer doesn't extrude correctly
I am new to 3D printing which we all are/were at some point. I have no clue how to address the issue which likely is reason why I haven't found the solution yet. So if you see that this question has ...
CommunityBot
- 1
0
votes
1
answer
2k
views
Unable to load new filament FlashForge Adventurer 3
I have a FlashForge Adventurer 3. I have just finished my sample filament today and tried to replace it with a new spool of filament. This new filament is by Hatchbox, instead of FlashForge. Besides ...
- 37.1k
1
vote
2
answers
121
views
Failure near the start point
The image below I indicated where the point where the tip of my extruder returns after changing the layer height, I don't know if I am right to call this point "Start Point" ...
The problem ...
- 37.1k
0
votes
0
answers
2k
views
Under extrusion on one side, but only while printing support material
Trying to print a bracket for pliers, however the support material on the left side always fails by under extruding. The model is left-right symetrical, so the support is the same for both sides. ...
- 37.1k
2
votes
1
answer
604
views
What are the dimensions of the FlashForge Creator Pro heating block?
I have a FlashForge Creator Pro, couple of years old. I'm looking to replace one or both of the heating blocks, as they're getting old and pretty gunked up. Instead of buying two blocks at \$30 each,...
- 37.1k
2
votes
0
answers
228
views
Z Offset Keeps Changing Flashforge Hunter
I am a newbie and I started having printing problems with my Flashforge Hunter.
I found out that with every calibration the building plate Z offset is getting larger by approx 0.1 mm to 0.2 ...
- 37.1k
3
votes
2
answers
697
views
I need assistance replacing the PTFE tube in the nozzle on our Flashforge dreamer
We disassembled everything in order to unclog the filament from the tube, but now I can't seem to get the nozzle to screw back in to the hotbed with the PTFE tube in place. Is there some kind of trick?...
- 59
5
votes
1
answer
556
views
PLA Filament Not Softening During Load w/ FlashForge Creator Pro
Recently, after printing fine for several weeks, I've gone to load in white PLA filament into the right extruder on my FlashForge Creator Pro and the extruder is not pulling the white PLA filament ...
- 223
5
votes
3
answers
2k
views
Nema Stepper used in Flashforge 3D printer
I am using Flashforge Creator Pro and a Flashforge Finder
I want to know which NEMA stepper model is used in each of these two printers, or is it NEMA 17 for both?
Their model numbers are:
...
- 22.5k