All Questions
14 questions with no upvoted or accepted answers
2
votes
2
answers
1k
views
Nozzle goes down after bed leveling BLTouch
I have two printers, one is an Anet A8 and the other one is a CreatBot DX plus. On both of them I installed a BLTouch, firstly on the DX and today on the A8. I have never had a problem with the probe, ...
- 29
1
vote
0
answers
94
views
Anet A8 keeps failing prints that it used to be able to complete and new ones
The most recognizable problem with my 3D printer is that the extruder stepper keeps clicking. As you can see in these 2 pictures it fails to extrude out plastic in time when doing retractions and when ...
- 11
1
vote
0
answers
108
views
Bioprinter does not extrude Anet A8 Marlin
I have a modified Anet A8 that is supposed to print hydrogels
(paper : Ultra-Low-Cost 3D Bioprinting, Kahl M et al. 2019).
For this to work, we do not need any temperature-related settings, however, I ...
- 19
1
vote
0
answers
34
views
Odd behaviour of steady feedrate increase
For some weeks I noticed really odd behaviour on my OctoPi controlled Anet A8. I'm using an MKS Gen L board with TMC2208 on this and constellation worked for a year now.
When starting a print, I ...
- 11
1
vote
0
answers
264
views
Filament getting stuck after 1.5 hours of printing
Problem: After about 1.5 hours of printing on my modified Anet A8 the (converted to Bowden) extruder begins to make a clicking noise. The filament is not being pushed through the hotend (E3D V6, it is ...
- 11
1
vote
0
answers
85
views
How to avoid line curvature in first layer of a 3D print
I have a problem with large lines in the first layer of my prints which have curvatures. The last layer has no problems. You can see the problem in the horizontal line of the "A", the rest of the "A" ...
- 11
1
vote
0
answers
184
views
PyCNC - How to configure for my setup?
I have replaced the main board of my Anet A8 printer with a Raspberry Pi based one, running PyCNC.
After many issues I have finally got to a point where all the motors work as well as heating and ...
- 111
0
votes
0
answers
29
views
Problems after successful first Benchy - Failed prints with same configuration (Anet A8)
I’m using an Anet A8 and recently printed my first Benchy successfully. The first print came out really well, but now, with the exact same configuration, all I get are failed prints. I’ve attached ...
0
votes
0
answers
76
views
Anet A8 inaccurate printing
I'm trying to print this with an Anet A8
It's supposed to be completely cylindrical but it's printing it all wobbly and with edges.
I'm a complete noob with 3D printing, so any tips would be highly ...
0
votes
1
answer
231
views
3 Extruders on SKR V1.1, how set up 2 in 1 out (Y piece), and 1 single extruder in latest Marlin?
On Anet A8 with SKR V1.1 32 bit board my intention is to use 3 extruders on my Anet A8, 1+2 via Y-piece on single nozzle, 3rd Extruder with 2nd nozzle. Need another stepper to connect to SKR V1.1 (10 ...
- 9
0
votes
0
answers
383
views
Got "Heating failed" error while heat catridge is working
I bought an Anet A8 Plus in January. Everything worked pretty well until one week ago. When I tried to print something, I got a "Heating Failed" error, as the hotend didn't get hot. I've ...
0
votes
0
answers
104
views
Anet A8 moves down into piece, destroying it, just before the printer is set to finish
I hope someone can help me figure out what's going on with my printer. I have been printing a couple of pieces and it's been printing perfectly. But for some reason every now and then, the printer ...
0
votes
0
answers
76
views
PyCNC - Z steppers screaming
I'm transforming my Anet A8 printer to Raspberry Pi driven using PyCNC. Things seem to look promising so far apart from the Z motor doing nothing but making screaming-like sound when supposed to be ...
- 111
0
votes
0
answers
376
views
Vibration marks when printing slowly on Y-axis
My Anet A8 prints come out with vibration marks when I print under 80 mm/s.
Above that value, it's fine.
Has anyone experienced something like this with any axis?
The Y-axis motor also ...
- 89